(Translated by https://www.hiragana.jp/)
! MAD INPUT DECK FOR BEAM LINE 2 ! CHICANE IN H-LINE NOT ENERGIZED ! 04/19/2010 Misha add sextupoles on 06/29/2010 IB:= 32.0 ! was 50/1.8 in 10/06/2008 edition ASSIGN,PRINT=out.txt BEAM, ENERGY=IB*1.8E-3, EXN=4*2.0E-6, EYN=4*2.0E-6, SIGE=0.01 HR:=BEAM[ENERGY]/2.99792458E-4 H: LINE=(HO00,HPOP1,HO01,HQ1,HO02,HQ2,HO03,HQ3,HO04,HPOP2, & CHO1,CHBEND1,CHO2,CHBEND2,CHO3,CHBEND3,CHO2,CHBEND4, & CHO4,HPOP3,HO06,HQ4,HO07,HQ5,HO08,HQ6,HO09,HPOP4, & HO10,m2,HO10,HPOP5,HO11,HQ7,HO12,HQ8,HO13,HQ9,HO14,HPOP6, & HO15,BPM5,HO16,Hendl) m2:marker HO00: DRIFT, L=0.20 HPOP1: MONITOR, L=0.00 HO01: DRIFT, L=0.17 HQ1: QUADRUPOLE, L=0.10, K1=IHQ1/4.4444E-3/HR HO02: DRIFT, L=0.20 HQ2: QUADRUPOLE, L=0.20, K1=IHQ2/4.4444E-3/HR HO03: DRIFT, L=0.20 HQ3: QUADRUPOLE, L=0.10, K1=IHQ3/4.4444E-3/HR HO04: DRIFT, L=0.17 HPOP2: MONITOR, L=0.00 ! Chicane not activated CHBEND1: SBEND, L=0.41, ANGLE=+0.0, E1=-0.0, E2=0.0, TILT CHBEND2: SBEND, L=CHBEND1[L], ANGLE=-CHBEND1[ANGLE], E1=-0.0, TILT CHBEND3: SBEND, L=CHBEND1[L], ANGLE=-CHBEND1[ANGLE], E2=0.0, TILT CHBEND4: SBEND, L=CHBEND1[L], ANGLE=CHBEND1[ANGLE], E1=-0.0, & E2=0.0, TILT ! Arc Length L=0.447 for ANGLE=20.0 CHO1: DRIFT, L=0.845 CHO2: DRIFT, L=0.08 CHO3: DRIFT, L=0.24 CHO4: DRIFT, L=0.535 HPOP3: MONITOR, L=0.00 HO06: DRIFT, L=0.17 HQ4: QUADRUPOLE, L=0.10, K1=IHQ4/4.4444E-3/HR HO07: DRIFT, L=0.20 HQ5: QUADRUPOLE, L=0.20, K1=IHQ5/4.4444E-3/HR HO08: DRIFT, L=0.20 HQ6: QUADRUPOLE, L=0.10, K1=IHQ6/4.4444E-3/HR HO09: DRIFT, L=0.17 HPOP4: MONITOR, L=0.00 HO10: DRIFT, L=1.50/2 HPOP5: MONITOR, L=0.00 HO11: DRIFT, L=0.17 HQ7: QUADRUPOLE, L=0.10, K1=IHQ7/4.4444E-3/HR HO12: DRIFT, L=0.20 HQ8: QUADRUPOLE, L=0.20, K1=IHQ8/4.4444E-3/HR HO13: DRIFT, L=0.20 HQ9: QUADRUPOLE, L=0.10, K1=IHQ9/4.4444E-3/HR HO14: DRIFT, L=0.17 HPOP6: MONITOR, L=0.00 HO15: DRIFT, L=0.25 BPM5: MONITOR, L=0.0000 HO16: DRIFT, L=0.28 Hendl: monitor, L=0.00 F1: LINE=(FD1,FO01,FP1,FO02,FQ1,FO03,HES,FO041,FS1,FO042,FQ2,FO05, & FP2,FO06,FQ3,FO07) FD1: SBEND, L=0.4000, ANGLE=-0.3491, HGAP=0.115, FINT=0.0 FO01: DRIFT, L=0.6705 FP1: MONITOR, L=0.0000 FO02: DRIFT, L=0.3500 FQ1: QUADRUPOLE, L=0.1000, K1=IFQ1/4.4444E-3/HR FO03: DRIFT, L=0.1925 HES: MONITOR, L=0.0000 FO041: DRIFT, L=1.08075 FS1: SEXTUPOLE, L=0.05, K2=IFS2/4.444E-3/HR ! -?- need calibration--!--------------- FO042: DRIFT, L=0.6775 FQ2: QUADRUPOLE, L=0.1000, K1=IFQ2/4.4444E-3/HR FO05: DRIFT, L=0.2230 FP2: MONITOR, L=0.0000 FO06: DRIFT, L=1.6654 FQ3: QUADRUPOLE, L=0.1000, K1=IFQ3/4.4444E-3/HR FO07: DRIFT, L=1.1520 FD2: SBEND, L=0.4000, ANGLE=0.3491, HGAP=0.015, FINT=0.5 ! Beam leaves line here if entering beamline 1 or continues along the remainder of beamline 0 if entering beamlines 2 or 3 F2: LINE=(FO08,FP3,FO09,mask,FO10,FQ4,FO111,FS2,FO112,FQ5,FO12,FP4,FO13) FO08: DRIFT, L=0.69 FP3: MONITOR, L=0.0000 FO09: DRIFT, L=0.0900 mask: MONITOR, L=0.0000 FO10: DRIFT, L=0.1700 FQ4: QUADRUPOLE, L=0.1000, K1=IFQ4/4.4444E-3/HR FO111: DRIFT, L=0.1500 FS2: SEXTUPOLE, L=0.05, K2=IFS2/4.444E-3/HR ! ??????? need calibration!!!!!!!!!!! FO112: DRIFT, L=1.8000 FQ5: QUADRUPOLE, L=0.1000, K1=IFQ5/4.4444E-3/HR FO12: DRIFT, L=0.4929 FP4: MONITOR, L=0.0000 FO13: DRIFT, L=0.5445 ! beam continues to either of beamlines 2 or 3 IHQ1:= 5*32*1.8/50 IHQ2:=-5*32*1.8/50 IHQ3:= 5.5*32*1.8/50 IHQ4:= 0 IHQ5:= 0 IHQ6:= 0 IHQ7:= -6.4*32*1.8/50 IHQ8:=-3*32*1.8/50 IHQ9:= 10.2*32*1.8/50 IFQ1:=-5.57*32*1.8/50 IFQ2:= 6.19*32*1.8/50 IFQ3:=-3.63*32*1.8/50 IFQ4:= 6.33*32*1.8/50 IFQ5:=-3.04*32*1.8/50 bx:= 10 ! startup twiss by:= 10 ax:= -1.000 ay:= -1.000 USE, PERIOD=(H,F1,F2) SELECT, TWISS, HPOP1 SELECT, TWISS, HPOP2 SELECT, TWISS, HPOP3 SELECT, TWISS, HPOP4 SELECT, TWISS, HPOP5 SELECT, TWISS, HPOP6 SELECT, TWISS, HES SELECT, TWISS, FP2 SELECT, TWISS, FP3 SELECT, TWISS, FP4 twiss,BETX=bx,BETY=by,ALFX=ax,ALFY=ay,SAVE plot,haxis=s, vaxis1=BETX,BETY, vaxis2=Dx,Dy, table=twiss, & Hmin=0, Hmax=30,Vmin=0,vmax=40,SPLINE, colour=100