Design and Realization of a Novel Buck-Boost Phase-Modular Three-Phase AC/DC Converter System with Low Component Number

Master Thesis
Spring Semester 2019

Author:

Aidar Zhetessov

ID: 15-948-268

Supervisor:

David Menzi

Professor:

Prof. Dr. J. W. Kolar

July 30, 2019

Abstract

Scalability and modularity are key features for future power converters, such that these systems can be easily employed in many applications with different electrical specifications. In this thesis, the potential of a new bidirectional phase-modular three-phase AC/DC converter with buck-boost capability is evaluated by means of studying two potential application cases and developing a hardware prototype for one of them.

The DC-DC inverting buck-boost converter is a well known and established topology. By connecting three such systems in parallel, a phase-modular bidirectional buck-boost DC-AC converter employing a minimum number of active components results, where for given AC voltage amplitudes, an arbitrary DC voltage can be generated and vice versa. Such a three-phase converter was not yet described in literature and this project aims at investigating the fundamental topology properties, as well as its performance limits. A hardware demonstrator is designed for one potential application in order to verify the basic operation and the expected high performance in terms of efficiency and power density.

See pages - of Task_Description.pdf

Chapter 1 Introduction

1.1 Background and Motivation

With the recent proliferation of power electronics in e-mobility and distributed renewable energy generation the demand for more efficient, plug-and-play, modular and compact bidirectional converters with voltage buck-boost capability is intensified. Example emerging applications are the Electric Vehicles (EV), their charging stations, grid-feeding converters with variable input voltage in microgrids, and some specific applications in a More Electric Aircraft. In case of Fuel Cell Vehicles (FCV), for instance, one wants to have full control over the machine torque irrespective of the fuel cell output voltage as long as the output power can be provided. The same holds true not only for the main motor, but also for an auxiliary one, which provides the compressed air needed for the Fuel Cell chemical reaction [1]. For the EV charging stations, the established standards require very wide range of both DC and AC voltage to be covered. The idea is to ensure compatibility between various EV manufacturers that employ different technologies. For microgrids, having a PV panel connected to the DC-link capacitor in a standard inverter setup, one obviously cannot ensure constant DC voltage at a certain level due to illumination variations. And even if an Energy Storage System (ESS) is there to reduce the DC voltage variations, a control system could require the converter to step up or down the AC bus voltage with respect to the input DC voltage in case of some microgrid transients. These again demand voltage buck-boost capability of the inverter.

Apart from buck-boost capability, other important performance metrics for the aforementioned applications can be listed as follows:

$\bullet$ Power Factor Correction (PFC) - the capability of the converter to absorb/feed an in-phase and clean AC currents from/to the mains/load.

$\bullet$ Operational Safety - the capability of delivering the required performance in presence of grid imbalance and faults. Safe two- and single-phase operation should also be considered here [2]-[3].

$\bullet$ Reliability - the capability of handing a high peak power, direct start up without pre-charging [2]-[3], as well as low complexity and thermal stress to ensure a long Mean Time To Failure (MTTF).

$\bullet$ Realization Effort - this could include manufacturing cost (phase-modularity), complexity (number of active components), control effort (number of sensors, gate drivers, computational burden), overvoltage-limiting effort as well as wiring and mounting effort (isolated mounting of active devices) [2]-[3].

$\bullet$ Power Density - an important parameter for a space-constrained application, such as in e-mobility.

Regarding the Realization Effort, [4] highlights the importance of phase modularity. According to [4], the industry-preferred approach favors the paralleling of single-phase converter units to form a three-phase high-power converter systems. Such a modular development approach has several advantages:

$\bullet$ Well-proven and reliable single-phase converter technology can be used immediately.

$\bullet$ No major change of the existing production line is required.

$\bullet$ The power expandability offers great flexibility in the development of power converter products for different power levels.

$\bullet$ There are fewer requirements for the maintenance and repair of power converter modules because standard single-phase converter units are used.

$\bullet$ Standard single-phase converter units do not require high-voltage devices that are normally needed in specially designed three-phase converters.

Bearing this in mind, phase modularity (both in terms of topology and associated control) is beneficial concerning manufacturing and maintenance aspects.

Conventional solutions for such buck-boost application would employ a cascaded converter system, e.g. a boost DC-DC converter with a buck-type Voltage Source Inverter (VSI). Essentially this cascade simply boosts the input DC voltage $V_{dc}$ through the boost DC-DC converter to increase the achievable output voltage range for a VSI. Considering the performance metrics stated above, there are many disadvantages associated with the cascaded converter structures in terms of realization effort (phase modularity) and power density. Indeed, a cascaded structure implies more components, cost, volume, losses, design effort etc. Moreover, in many particular cases cascaded structures imply more time-scale separation steps in the control system, which imposes other control-related complications and stability concerns. Therefore, for the mentioned applications it is desired to have a single-stage (bidirectional) buck-boost AC-DC converter, playing the role of a generalized AC-DC interface.

Having observed the aforementioned deficiencies of a conventional solution, several single-stage buck-boost three-phase converter concepts can be found in the literature. A thorough analysis and comparison of three converter concepts was presented in [2]. Also there is a buck-boost three-phase AC-DC converter with inherent PFC capability and simple control presented in [5], its single-switch counterpart from [6] as well as phase-modular and direct three-phase single-stage flyback-type power factor correctors from [3].

Apart from these literature solutions, more options of such three-phase topologies could be generated by paralleling three single-phase DC-DC converters with buck-boost capability, as it was stated in [7]. In buck-boost DC-DC converters operated in DC-AC mode, usually the DC link voltage midpoint is considered the AC reference point (open star point of the machine for instance). By paralleling DC-DC converters, the AC voltages are referenced to negative DC rail, thus one introduces a CM voltage shift. This CM voltage degree of freedom can be used to realize a three-phase DC-AC converter using three DC-DC converter (phase) modules [7].

Partially inspired by [1], [3] and [7], a new topology, the three-phase inverting buck-boost converter, is presented and analyzed in this thesis (Fig. 1.1). Essentially, this solution results from paralleling three inverting buck-boost DC-DC converters. This novel topology is an interesting alternative to the mentioned solutions, as it is proven to have all the required performance metrics above: it has a low number of semiconductors and passives, provides voltage buck-boost capability, single-stage high-frequency energy conversion and is phase-modular both in terms of topology and control. Apart from these advantages, it has a mentioned Common Mode (CM) AC voltage degree of freedom, which can be used to adapt the modulation and, consequently, improve converter losses and semiconductor utilization. Together, these factors are in favor of a power dense design, thus making the investigation of this topology interesting. Therefore, the objective of this thesis is to explore the applicability of a three-phase inverting buck-boost converter topology in the mentioned emerging applications. This is done through the design of a prototype for a selected application. Particularly considered applications comprise (but are not limited to) a rectifier for an Electro Hydrostatic Actuator (EHA) in a More Electric Aircraft and an auxiliary motor’s inverter in a Fuel Cell Vehicle (FCV).

Refer to caption — Figure 1.1: Inverting Buck-Boost Converter Topology

1.2 Outline

This thesis has five chapters, the first one being an introduction. The chapter 2 provides a general information of interest regarding the topology, such as topology derivation, operating principle, review of hard- and soft-switched operation and applicable modulation schemes. Chapter 3 explores the applicability potential of the proposed topology in a rectifier application within the context of a More Electric Aircraft. This is done by designing appropriate modulation and associated control for the topology in rectifier mode. Chapter 4 does the same for inverter application within the context of a Fuel Cell Vehicle. In addition, the prototype design process is thoroughly explained and a virtual prototype is presented. The thesis is concluded in chapter 5. As a side project, a calorimetric switching loss measurement setup for a GaN GIT transistor is addressed in Appendix A.

Chapter 2 Converter Fundamentals and Modulation Scheme Options

This chapter is dedicated to the theoretical background of the three-phase inverting buck-boost converter. The information of this chapter lays the background on the converter topology and operation. All subsequent chapters of the thesis will build up on this background. The chapter consists of four sections. In the first section we discuss the derivation of the three-phase inverting buck-boost converter topology. The second section reveals the basic operating principle of the topology, starting from a DC-DC inverting buck-boost phase module and proceeding to the three-phase DC-AC operation. The third section is a brief review of a standard half-bridge hard- and soft-switching operation. This information is useful because, as it was already shown in Fig. 1.1, the half-bridge constitutes a basic building block of our converter. Moreover, understanding hard- and soft-switched operation will be useful in subsequent evaluation and comparison of modulation schemes. The fourth section proposes several modulation scheme candidates and discusses respective operating principles.

2.1 Derivation of the Three-Phase Inverting Buck-Boost Converter Topology

Before studying the operation of the converter in more detail, it is worth justifying the use of a three-phase inverting buck-boost converter topology first. To do that, one starts with the aforementioned conventional cascaded solution - DC-DC boost converter and Voltage-Source Inverter (VSI, Fig. 2.1a). The VSI can also be seen as three paralleled DC-DC buck converters that can generate output voltages between [0.. $V_{pn}$ ], where $V_{pn}$ is the intermediate DC link voltage. Provided unipolarity of the output voltages ([0.. $V_{pn}$ ] $\geq$ 0) three DC-DC buck converters can drive a three-phase AC load only with a positive Common Mode (CM) voltage offset between the load star point and the DC- rail. Moreover, the maximum AC output phase voltage amplitude is limited to $\hat{V}_{AC,max}=V_{pn}/2$ due to buck converter upper limit of $V_{pn}$ . In these conditions to provide the overall buck-boost capability one has to boost up the DC input voltage $V_{dc}$ by employing the preceding DC-DC boost stage (Fig. 2.1a).

On the other hand, instead of paralleling three DC-DC buck stages one could parallel three DC-DC inverting buck-boost stages to result in a three-phase inverting buck-boost converter instead of a VSI (Fig. 2.1b). This proposal is advantageous because the three-phase inverting buck-boost converter provides the voltage buck-boost capability without the preceding DC-DC boost stage, while keeping the number of active/passive components the same as in the VSI stage. It is worth mentioning that the output voltage is unipolar and inverted (as the name suggests), meaning that the converter features a negative CM voltage offset between the load star point and the DC- rail. This is reflected in polarity change of $V_{mn}$ in Fig. 2.1b compared to Fig. 2.1a.

2.2 Inverting Buck-Boost Converter Operating Principle

This section deals with the basic operating principle of the three-phase inverting buck-boost converter, starting from a DC-DC inverting buck-boost stage and proceeding to the three-phase DC-AC operation. As it was mentioned, this procedure is inspired by [1], [3] and [7].

2.2.1 DC-DC operation of one inverting buck-boost stage

The well-known DC-DC inverting buck-boost topology 2.1(a) has a full control over its output DC voltage. To understand its operation, consider steady state with $V_{dc}=|V_{an}|$ . In that case, possible steady state buck-boost inductor current waveforms for two values of inductance are shown in Fig. 2.1(b). There are three distinct time intervals within the depicted switching period:

$\bullet$ First, the period starts with the transistor $T_{2}$ turned on and the inductor current equal to its average value $\bar{I}_{L}$ as shown in Fig. 2.1(b). The inductor is demagnetized by the output capacitor $C$ during the first interval (number $1$ red demagnetization loop in Fig. 2.1(a)).

$\bullet$ Second, after some time (equal to the quarter of the switching period in this case) transistor $T_{2}$ is turned off and the transistor $T_{1}$ is turned on, signifying the start of the second interval. The buck-boost inductor is now magnetized by the input DC capacitor $C_{dc}$ . Second interval corresponds to number $2$ blue magnetization loop in Fig. 2.1(a).

$\bullet$ Third, after the second interval (which is equal to half of the switching period in this case) transistor $T_{1}$ is turned off and the transistor $T_{2}$ is turned on back again, signifying the start of the third interval. The buck-boost inductor is now demagnetized back by the output capacitor $C$ . This interval corresponds to number $3$ red demagnetization loop in Fig. 2.1(a).

During the first and the third (red) time intervals, the inductor demagnetization is described by the following equation: $-|V_{an}|=\frac{Ldi_{L}}{dt}$ . Similarly, for the second (blue) time interval the inductor magnetization is described by: $V_{dc}=\frac{Ldi_{L}}{dt}$ . Defining the duty cycle $d$ to be a fraction of the switching period $T_{s}$ corresponding to the turn-on state of $T_{1}$ (time interval $2$ ), and writing the steady state inductor volt-second balance we arrive at the following equations:

\begin{split}&V_{dc}dT_{s}-|V_{an}|(1-d)T_{s}=0\\ &V_{dc}dT_{s}=L\Delta I_{pkpk}\\ \end{split}

(2.1)

From (2.1) the converter duty cycle and the peak-to-peak inductor current ripple $I_{pkpk}$ can be derived as a function of input and output voltages, inductance value and the switching frequency $f_{s}$ as follows:

\begin{split}d&=\frac{|V_{an}|}{V_{dc}+|V_{an}|}\\ I_{pkpk}&=\frac{|V_{an}|V_{dc}}{Lf_{s}(|V_{an}|+V_{dc})}\\ \end{split}

(2.2)

From the equation (2.2) it is seen that in case $V_{dc}=|V_{an}|$ the duty cycle $d$ equals $0.5$ , which coincides with the interval durations in Fig. 2.1(b). Equation (2.2) with its non-linear input and output voltage dependent duty cycle and current ripple, combined with Fig. 2.2, provide a comprehensive overview of the DC-DC inverting buck-boost converter steady state operation.

2.2.2 DC-AC operation of one inverting buck-boost stage

To operate the inverting buck-boost stage from Fig. 2.1(a) in a DC-AC mode, one could zoom out in time scale and slowly vary the steady state duty cycle from (2.2) in a non-linear manner, similar to [1]. For that though, the fundamental frequency $f_{o}$ of the converter AC operation should be much slower than the switching frequency ( $f_{o}<<f_{s}$ ) to ensure a quasi-DC-DC operation within any given switching period. Potential steady state waveforms of an inverting buck-boost stage DC-AC operation are depicted in Fig. 2.3.

In Fig. 2.3 we can see that provided the duty cycle variation within one switching period is negligible, the converter always operates in quasi-DC-DC mode as it can be seen in the magnification from Fig. 2.3d to Fig. 2.3b. Moreover, Fig. 2.3c shows a nice sinusoidal output voltage $-V_{an}$ with a negative DC offset. In this case the offset is equal to $-V_{dc}$ , which can also be seen from the Fig. 2.3a, because the duty cycle equals $0.5$ once in every half-fundamental period interval. Finally, Fig. 2.3a illustrates the non-linear relation between duty cycle and the output voltage, since the duty cycle is not sinusoidal for an offsetted sinusoidal output voltage.

2.2.3 DC-AC operation of three paralleled inverting buck-boost stages

Following the idea from [7], also shown in Fig. 2.1c, a three-phase inverting buck-boost converter can be assembled from three DC-AC operated inverting buck-boost stages. In this case, unlike the single-phase case, only three AC terminals $a,b,c$ (without negative DC terminal $n$ ) are provided from AC side as it is shown in Fig. 2.4.

Considering the example case depicted in Fig. 2.4, three-phase converter can be operated as an inverter feeding a resistive load. Fig. 2.3(b) shows the input DC voltage and the output capacitor voltages when each paralleled inverting buck-boost stage is operated with a standard PWM and a $120$ degree phase shifted duty cycle from Fig. 2.3a for each phase. It can be seen that $-V_{an,bn,cn}$ are always less than zero due to the nature of the topology. In a three-phase context this property can be referred to as an already mentioned Common Mode offset $V_{nm}$ (Fig. 2.3(a)).

2.3 Review of a Hard- and Soft-Switching Operation

Before diving into the various modulation options, a brief review of hard- and soft-switched operation would be useful, as the modulations will be evaluated with respect to the impact on the switching losses. To do that, consider an example of a DC-DC buck converter (Fig. 2.4(a)) in steady state operation with $V_{in}>V_{an}$ .

Possible steady state inductor current waveforms are provided in Fig. 2.4(b) for two inductance values. The duty cycle and the inductor current ripple for a buck converter are given by:

\begin{split}d&=V_{an}/V_{in}\\ \Delta I_{L}&=(1-d)T_{s}V_{an}/L=(V_{in}-V_{an})T_{s}V_{an}/V_{in}L\\ \end{split}

(2.3)

From the equation for the inductor current ripple $\Delta I_{L}$ it is seen that the ripple is proportional to the switching period $T_{s}$ and inversely proportional to the inductance value $L$ .

Consider the waveform corresponding to the inductance value $L_{1}$ . From Fig. 2.4(b) it is seen that the half of the inductor current ripple $\Delta I_{L}$ is less than the average value of the inductor current $\bar{I}_{L}$ such that both switching transitions occur at positive instantaneous inductor current values. If one now analyzes the first switching transition, depicted by a red dot, in more detail, it corresponds to the turn-off of the transistor T2 and subsequent turn-on of the transistor T1 after a dead time interval. Bearing in mind the positive instantaneous inductor current (directed from the half-bridge to the output capacitor), after turn-off of the transistor T2 the inductor current continues flowing through it using the respective body diode. As soon as the dead time interval is finished, the transistor T1 is turned on and the inductor current commutates from the body diode of the transistor T2 to the channel of the transistor T1. The energy stored in the output capacitance of the transistor T1, which is equal to $C_{OSS}V_{in}^{2}/2$ , is dissipated in the transistor T1 at the instant of turn-on, thus forming a hard switched transition of the half-bridge (a red dot in Fig. 2.4(b)).

Regarding the second transition of the switching period under consideration, it is seen that the half of the inductor current ripple $\Delta I_{L}$ and the average value of the inductor current $\bar{I}_{L}$ add up to form a highly positive instantaneous inductor current. If one now analyzes the second switching transition, depicted by a green dot, in more detail, it corresponds to the turn-off of the transistor T1 and subsequent turn-on of the transistor T2 after a dead time interval. Bearing in mind the positive instantaneous inductor current (directed from the half-bridge to the output capacitor), after the turn-off of the transistor T1 the inductor current starts charging up the output capacitance $C_{OSS}$ of the transistor T1 and discharging the output capacitance $C_{OSS}$ of the transistor T2. Provided the dead time interval is long enough and the inductor current is large enough, the charge-discharge procedure of the output capacitances is finished before the end of the dead time interval. After the end of the charge-discharge procedure, the inductor current commutated to the body diode of the transistor T2. Corresponding voltages of the output capacitances of the transistors T1 and T2 at the end of the dead time interval are $V_{in}$ and $0$ respectively, so that there is no energy stored in the output capacitance of the transistor T2 at the instant of turning on after the dead time. This forms a soft-switched transition of the half-bridge (a green dot in Fig. 2.4(b)).

The derivations for the dead time interval and the minimum inductor current requirements can be obtained from literature. For example, in [8] $i_{o}$ is defined as

i_{o}\geq\text{max}\big{(}\text{max}(V_{in}),\text{max}(V_{an})\big{)}\sqrt{% \frac{C_{OSS}}{L}}

(2.4)

Now consider the second inductor current waveform in Fig. 2.4(b). It corresponds to an inductance value $L_{2}<L_{1}$ so that $\Delta I_{L}$ is increased (dashed line). From Fig. 2.4(b) it is seen that the half of the inductor current ripple $\Delta I_{L}$ is more than the average value of the inductor current $\bar{I}_{L}$ so that two switching transitions occur at negative and positive instantaneous inductor current values, respectively. If one now analyzes the first switching transition, depicted by a green dot at $-i_{o}$ current value, in more detail, it again corresponds to the turn-off of the transistor T2 and subsequent turn-on of the transistor T1 after the dead time interval. Bearing in mind the negative instantaneous inductor current (directed from the output capacitor to the half-bridge), after the turn-off of the transistor T2 the inductor current starts charging the output capacitance of the transistor T2 and discharging that of T1. Provided the dead time interval is long enough and the inductor current is large enough (which is true for the waveform under consideration), the charge-discharge procedure of the output capacitances is finished before the end of the dead time interval. After the end of the charge-discharge procedure, the inductor current commutated to the body diode of the transistor T1. The corresponding voltages of the output capacitances of the transistors T1 and T2 at the end of the dead time interval are $0$ and $V_{in}$ , respectively, so that there is no energy stored in the output capacitance of the transistor T1 at the instant of turning on after the dead time. This forms a soft switched transition of the half-bridge (a green dot in Fig. 2.4(b)).

In this section we’ve reviewed a basic model for hard- and soft-switching operation of one half-bridge. We’ve seen that it is possible to operate a half-bridge in a soft-switched manner, thus resulting in a significantly reduced switching losses. The main idea is to have an inductor-impressed current of a sufficient magnitude flowing into the half-bridge (in case of transition from low to high) or out of the half-bridge (in case of transition from high to low) within the dead time interval of sufficient length. The same considerations can also be applied to the half-bridge of the DC-DC inverting buck-boost converter. The only difference is in the blocking voltage of the half-bridge. While in DC-DC buck converter the blocking voltage is equal to $V_{in}$ , in DC-DC inverting buck-boost converter (a single phase in Fig. 2.1c) the blocking voltage is equal to $V_{in}+V_{an}$ , which is the sum of the input and output voltages according to Kirchoff’s Voltage Law applied to the outer loop through $T_{1},T_{2},C$ and $C_{dc}$ in Fig. 2.1c.

2.3.1 MOSFET semiconductor losses

The equation 2.4 provides only a theoretical estimation of the minimum soft-switching current. On a separate note, there is a comprehensive experimental evaluation of the semiconductor losses provided in [9]. In that work, a loss map of a 900 V SiC MOSFET half-bridge was experimentally obtained (c.f. Fig. 2.6). The loss map for this device is of particular interest in this chapter due to the applicability of the device in an Electro Hydrostatic Actuator rectifier application, which will be discussed in the next chapter.

Here the turn-on graph on the left provides the half-bridge switching losses in case of a hard-switched transition (e.g. the red dot in Fig. 2.4(b)). From this graph we can see that the switching loss is proportional to the half-bridge voltage and the switched current. Even in case of zero switched current (Zero Current Switching) there is still a substantial loss originating from the energy stored in the output capacitance of the transistor $E_{OSS}=C_{OSS}V_{in}^{2}/2$ , which motivates the soft-switching.

The turn off graph on the right provides the half-bridge switching losses in case of a soft transition (e.g. a green dot in Fig. 2.4(b)). From this graph we can see that the switching loss is still proportional to the half-bridge voltage and the switched current, although the losses are considerably lower than those of the turn on graph. These dependencies are expected, since both hard- and soft-switching losses are essentially the voltage-current overlap areas in the channel of the switch. At low values of the switched current the switching loss becomes negligible as there is almost no voltage-current overlap area. This is an example of a complete soft-switching. Note that the data for a very low values of the switched current are not shown because at those values the secondary effects, which change based on the application, such as the duration of the dead time, $L/C_{OSS}$ ratio etc., start affecting the measurements. The respective transitions become partially hard and at zero current the loss figures coincide with those of ZCS, ensuring the continuity of the loss map.

2.4 Modulation Schemes for the Three-Phase Inverting Buck-Boost Converter

Having understood the basic operating principle of the three-phase topology at hand and revisited the hard- and soft-switching mechanisms, this section introduces three modulation scheme candidates - standard Pulse Width Modulation (PWM), Discontinuous Pulse Width Modulation (DPWM) and a Boundary Conduction Mode (BCM). For all three candidates the steady state theoretical three-phase converter waveforms are presented. In these waveforms any effect of the converter reactive components was neglected. In particular, the voltage drops over the buck-boost inductances and reactive currents consumed by AC-side capacitors were neglected due to the fact that respective voltage/current amplitudes are small compared to the nominal output voltage/current amplitudes. Moreover, for each modulation the envelopes of the buck-boost inductor currents are also depicted as a green/red lines, corresponding to soft-/hard-switched transitions respectively.

2.4.1 Standard Pulse Width Modulation (PWM)

The first modulation candidate is standard Pulse Width Modulation (PWM). The concept of PWM is simple: provide a large enough constant CM offset $V_{CM}$ , such that the AC-side voltages $V_{Ca},V_{Cb},V_{Cc}$ are strictly unipolar throughout the fundamental period $T_{o}$ , and apply the non-linear duty cycles (2.2) in each phase to yield the sinusoidal Differential Mode (DM) voltages. Fig. 2.7 shows the steady state theoretical PWM waveforms of the three-phase inverting buck-boost converter.

Fig. 2.7a-b tell us that the duty cycles below/above 0.5 correspond to buck/boost phase operation respectively. Fig. 2.7c depicts the AC-side load currents. Fig. 2.7d shows the phase $a$ buck-boost inductor current without taking into account the reactive capacitive currents of the AC-side. Although, strictly speaking, these reactive currents have to be incorporated for a proper modulation evaluation, the effect of these currents is relatively small, especially when AC-side capacitances are selected such that the reactive currents remain small compared to the load currents. Thus, for evaluation and comparison purposes, capacitive current and inductive voltage drop contributions are neglected in the presented steady state theoretical waveforms.

2.4.2 Discontinuous Pulse Width Modulation (DPWM)

The second modulation candidate is Discontinuous Pulse Width Modulation (DPWM), inspired by [1]. The concept of DPWM is as follows: use the CM offset $V_{CM}$ as a degree of freedom (DOF) and shape it in a way that results in a reduced blocking voltage per switch and switching actions compared to standard PWM (compare Fig. 2.7b, 2.7d to Fig. 2.8b, 2.8d). Fig. 2.8 shows the steady state theoretical DPWM waveforms of the three-phase inverting buck-boost converter.

As it can be seen from Fig. 2.8a, the duty cycles are clamped to zero for one third of the fundamental period. This can also be seen from Fig. 2.8c, where phase $a$ switching frequency equals zero (no switching) for one-third of the fundamental period. Fig. 2.8d shows the phase $a$ buck-boost inductor current without taking into account the reactive capacitive currents of the AC-side. In this idealized case one would expect the inductor current to be exactly equal to the sinusoidal phase current for the duration of clamping, which can actually be observed in the figure. Moreover, phases are almost purely soft-switched due to DPWM as it can be seen from Fig. 2.8d. Regarding the phase voltages in Fig. 2.8b, they are obviously far from sinusoidal when referenced to the negative DC rail of the converter (point $n$ in Fig. 3.1). However, these voltages are purely sinusoidal when referenced to the star point of the grid (point $m$ in Fig. 3.1). Indeed, consider phase $a$ voltage relations (Fig. 2.9). From the schematic one can see that:

V_{Ca}=V_{an}=V_{a}+V_{mn}=V_{a}+V_{CM}=V_{Ca,DM}+V_{CM}

(2.5)

The relation $V_{an}=V_{a}+V_{CM}$ is easily seen in Fig. 2.9a, thus proving that AC-side voltage is purely sinusoidal when referenced to the grid star point.

2.4.3 Boundary (Triangular) Conduction Mode (BCM or TCM)

The third modulation candidate is Boundary Condution Mode (BCM), inspired by [11]. The concept of BCM is as follows: use the per-phase switching frequency $f_{s}$ as a degree of freedom (DOF) and shape it in a way that results in a pure soft-switched operation throughout the fundamental period $T_{o}$ . Fig. 2.10 shows the steady state theoretical BCM waveforms of the three-phase inverting buck-boost converter.

Fig. 2.10a immediately reveals the qualitative difference between BCM and PWM/DPWM. Indeed, for BCM the duty cycle $d=f(f_{s})$ as this modulation scheme utilizes the variable switching frequency DOF to facilitate a soft-switched operation throughout the fundamental period. Instead of the duty cycles one plots the switching times $t_{s}$ and $T_{s}$ , where $t_{s}$ stands for the switching instance of the respective phase within the switching period and $T_{s}$ stands for the final switching transition of the period. In this context, the duty cycle can be defined as $d=\frac{t_{s}}{T_{s}}$ . Fig. 2.10d shows the phase $a$ buck-boost inductor current without taking into account the reactive capacitive currents of the AC-side. It can be seen that BCM ensures soft switching throughout the fundamental period. Also the peak/ripple inductor currents are slightly reduced compared to DPWM/PWM (compare Fig. 2.7d, 2.8d to Fig. 2.10d), thus potentially improving the switching losses as well as the conduction losses both in semiconductors and inductors. Fig. 2.10c depicts the switching frequency variation over the fundamental period. Two clear valleys below the maximum switching frequency of 300 kHz are observed. Taking into account these valleys, the input filter has to be designed for the minimal frequency of the CISPR band (150 kHz for rectifier applications), thus resulting in elevated filtering effort.

2.4.4 Conclusion

To sum up, remember that all three modulations are applicable to the Inverswandler irrespective of the application. Thus, the choice of modulation has to be done based on the quantitative evaluation and comparison, which takes into account the electrical specifications of an application at hand. Up to this point though, all the analysis was generic. In the next chapter, mentioned evaluation will be performed.

Chapter 3 Modulation, Control and Evaluation of the Three-Phase Inverting Buck-Boost Converter as a Rectifier

This chapter deals with the evaluation and selection of a modulation scheme, and control system design for the three-phase inverting buck-boost converter as a rectifier for an Electro-Hydrostatic Actuator (EHA) application in a More Electric Aircraft. Section one introduces the topology as a three-phase rectifier, and the electrical specifications. Also it discusses the component design, since not only the electrical specifications, but also the component designs are important for performance evaluation. Next, section two evaluates and compares the modulation scheme candidates from the previous chapter in the context of application at hand. One modulation is selected to be implemented in a closed-loop control scheme. Rectifier control for the selected modulation is addressed in section three. Challenges in the closed-loop rectifier control implementation are identified, and ameliorating measures (both software and hardware) are proposed for those in section four. Finally, section five summarizes the study of the three-phase inverting buck-boost converter within the rectifier application context.

3.1 Topology and Electrical Specifications in Rectifier Mode

Regarding applications for a More Electric Aircraft, the authors of [2] compare various three-phase AC-DC converter concepts for a drive train of an Electro-Hydrostatic Actuator (EHA). EHA is an actuator system that uses a high-power stepper motor to precisely control the pump position and pressure inside the hydraulic cylinder, which in turn is used to control the plate positions on the wings for aircraft positioning. Conventional designs used mechanical valve control to change the pressure in the hydraulic cylinder manually. The EHA provides redundancy (robustness), simplicity in system design and operation, energy economy and weight reduction. In this application, analyzed AC-DC converters are used to feed the DC link of the motor-driving inverter from the aircraft on-board mains. Here the advantage of having a controllable buck-boost output voltage is the capability of handling a wide input voltage range from the mains while maintaining the favorable output voltage.

The three-phase inverting buck-boost converter topology and the electrical specifications for a rectifier operation within the EHA application are shown in Fig. 3.1 and Table 3.1 below. The first set of specifications in Table 3.1 (starting with power rating and ending with THD) are the direct application requirements. Note that the rectifier has to provide a constant DC voltage and output power in the conditions of voltage- and frequency-oscillating grid, while maintaining a very high power factor and grid current quality. Although the grid voltage fluctuations are not that wide, the DC voltage is defined such that the buck-boost capability is required. The load resistor $R_{dc}$ is used to model the load behavior and is selected such that 600W of power are consumed at 270V DC link voltage. The second set of specifications in Table 3.1 (starting with operating switching frequency and ending with maximum switching frequency limit) are the derived electrical specifications. The derivation reasoning behind those is provided below.

Table 3.1: System specifications for a rectifier application

Parameter	Value	Unit	Param. Explanation (Given $\|$ Derived)
$P$	$600$	W	Rectifier power rating
$U_{o}$	$115\pm 15\%$	Vrms	Input grid phase voltage rms with tolerance
$V_{dc}$	$270$	V	Output DC voltage
$f_{o}$	$360-800$	Hz	Grid frequency range
$PF$	$>99\%$	-	Power factor requirement for $[50-100]\%$ load
$THD$	$<5\%$	-	Grid phase current THD requirement
$f_{s}$	$140$	kHz	Switching frequency
$L$	$75$	$\mu$ H	Buck-boost inductance
$L_{f}$	$75$	$\mu$ H	Grid-side filter inductance
$C$	$1$	$\mu$ F	Grid-side phase capacitance
$C_{dc}$	$10$	$\mu$ F	Load-side DC capacitance
Device	SiC 900V	-	Semiconductor: 1 x 900V, 30mOhm SiC [10]
$f_{s,max}$	$300$	kHz	Maximum switching frequency (BCM)

$\bullet$ First, the switching frequency $f_{s}$ was selected to be 140kHz because this value is at the lower limit of the regulated frequency band of the DO160 airborne equipment standard (between 150kHz - 30MHz for aviation applications [12]). By selecting 140kHz switching frequency we ensure that the first regulated switching frequency harmonic is 280kHz. Since the first regulated harmonic determines the corner frequencies of our input filter stages, the higher the regulated harmonic is, the higher the filter corner frequencies will be. Thus, the size of the filter is expected to reduce considerably. Bearing in mind the stringent application requirements on the grid current quality, having the first regulated harmonic as high is possible is beneficial. From the overall system perspective, of course one could consider switching frequencies above 140kHz. Ideally, in a proper Pareto analysis the switching frequency is a Degree Of Freedom (DOF), but for now the objective is to compare the modulation schemes for a single set of electrical specifications.

$\bullet$ Second, the buck-boost inductance value $L$ was selected to be 75 $\mu$ H because at this value the inductor current ripple is just large enough such that the Discontinuous Pulse Width Modulation (DPWM) results in complete soft-switching converter throughout the whole fundamental period, while standard PWM is soft-switched over a considerable part of the fundamental period as we will see in the later sections. On the other hand, the selected inductance value precludes the current ripple from becoming too large, which would increase the converter conduction losses. Bearing in mind that BCM employs variable switching frequency to facilitate soft-switching throughout the whole fundamental period, having the other two modulation candidates (PWM and DPWM) predominantly soft-switched provides a fair comparison between the three. In addition, the per-phase inverting buck-boost converter inherently features a high peak-to-average buck-boost inductor current ratio due to the discontinuous input-output power transfer. This inherent disadvantage in terms of converter conduction losses can be used to reduce the corresponding switching losses by allowing large current ripple with consequent inductor current-reversals needed for soft-switching. Regarding the filter inductor value, its value depends on the buck-boost inductance and AC-side capacitance values. The objective here is to filter the grid phase currents to comply with stringent current quality requirement. The filter inductance was iteratively simulated and selected to be 75 $\mu$ H, but in general this value is not strict and can be subject to change depending on aforementioned inductance and capacitance values.

$\bullet$ Third, the AC-side capacitance per phase was iteratively simulated and selected to be 1 $\mu$ F because it provides a good compromise between the grid-side voltage ripple and the capacitive current consumption. Indeed, in case AC-side capacitance is too small, the respective voltage ripple will become too large, potentially deteriorating the AC-side current quality (THD, PF) or even closed-loop control stability. On the other hand, in case AC-side capacitance is too large, the reactive current consumed by that capacitor will become large, resulting in elevated converter current values and conduction losses. Regarding the DC-side capacitance, it was iteratively simulated and selected to be 10 $\mu$ F because this value is enough to suppress the DC-side voltage ripple to $\pm 5\%$ .

$\bullet$ Finally, the maximum switching frequency for BCM case was selected to be 300kHz. The objective of such a choice is to limit the occurring switching losses near the fundamental zero-crossing of the buck-boost inductor current. At 300kHz the switching losses already dominate the conduction losses of the semiconductor by far, increasing the switching frequency higher could result in too much losses and controllability (gate driver) problems. Based on this reasoning, the limit of 300kHz was selected.

$\bullet$ Capacitor realization. To evaluate the effect of modulation on the converter performance, apart from the electrical specifications of capacitance and inductance, one also needs to determine the respective capacitor and inductor realizations, because the converter efficiency and power density depend on the volumes and losses of the respective components. The designs are determined using existing component scripts. Regarding capacitors, only film capacitors have been considered both for AC and DC-side. There are two reasons for that. First, in a proper converter design with a full Pareto optimization, the capacitor losses tend to be small compared to other component losses and this is well captured in our modulation evaluation, because film capacitors are lossless in a good approximation. Second, film capacitors are the least power dense and the most sensitive to the rated voltage variations. By utilizing them in the modulation evaluation one can more easily distinguish the effects of modulation-dependent parameters on the volume of the capacitive components.

$\bullet$ Inductor realization. Regarding the buck-boost inductors, the component script sweeps through all the possible core-coil combinations that result in the specified inductance value and outputs the losses-volume scatter graph, where each individual inductor design corresponds to a point. For a proper converter design, factors like inductor shape, fill-factor, manufacturing process etc. would have to be considered. For a qualitative modulation comparison, however, it is enough to pick a simply viable inductor design that comprehensively captures the expected characteristics of a properly designed inductor. Generally, those expected characteristics comprise a small volume and low losses. From these considerations, it was decided to estimate the volume-loss product for each inductor and simply pick the design with minimum product. By doing so we ensure that our modulation comparison outputs a reliable results, because irrespective of the final inductor design, it will have similar performance characteristics as the design with minimum loss-volume product.

3.2 Comparison of Modulation Schemes

Having presented the electrical specifications and the converter design guidelines, this section deals with the modulation comparison. Evaluated performance metrics comprise theoretical converter volume, losses and cost. Volume is estimated as a sum of boxed component volumes. The passives (capacitors, inductors) are designed based on the procedures above and volumes/losses are estimated. For example, the blue line in Fig. 2.7d is the buck-boost inductor current average over the fundamental period. From this line as well as the instantaneous ripple one can estimate the inductor current and, consequently, losses. Regarding semiconductors, loss estimation is done using the instantaneous voltage/currents across the devices at switching instances and the loss map (shown in Fig. 2.6). From these, estimated performances are presented in Fig. 3.2 and Table 3.2.

Table 3.2: Comparison of modulation performances for nominal operating conditions

Parameter	PWM	DPWM	BCM	Unit	Param. explanation
$I_{L,rms}$	4.3	3.8	3.5	A	Buck-boost inductor rms current
$I_{L,rms}^{2}$	18.2	14.4	12.2	A ${}^{2}$	Buck-boost inductor rms ${}^{2}$ current
$I_{L,max}$	12.7	11.2	11.3	A	Buck-boost inductor max. current
$f_{sw,avg}$	140	91	200	kHz	Average switching frequency
$f_{sw,max}$	140	140	300	kHz	Maximum switching frequency
$f_{sw,min}$	140	0	37	kHz	Minimum switching frequency
$V_{ss,max}$	611.5	551.6	611.5	V	Maximum soft-switched voltage
$I_{ss,max}$	12.7	11.2	11.3	A	Maximum soft-switched current
$V_{ss,avg}$	498.8	404.0	448.9	V	Average soft-switched voltage
$I_{ss,avg}$	5.6	3.4	3.2	A	Average soft-switched current
$V_{hs,max}$	319.9	-	-	V	Maximum hard-switched voltage
$I_{hs,max}$	1.9	-	-	A	Maximum hard-switched current
$V_{hs,avg}$	299.1	-	-	V	Average hard-switched voltage
$I_{hs,avg}$	1.2	-	-	A	Average hard-switched current

From the comparison it is seen that both DPWM and BCM are expected to show a comparable performance in terms of volume, losses and cost, which is better than that of standard PWM. Indeed, the comparison reveals the same potential converter volume and cost for DPWM/BCM, meaning that the small differences in the respective buck-boost inductor current waveforms are not significant enough to opt for a different inductors/capacitors realization. Nevertheless, small waveform differences are reflected in the loss distribution, where DPWM slightly outperforms the BCM. This result, however, cannot be generalized, as for a slightly different inductor realization or a varying rectifier grid frequency/voltage, the result can be different.

Finally, the decisive factors in modulation selection are the control complexity and filtering considerations. BCM features a very complex control with its current zero-crossing detection techniques. Apart from that, the BCM filter is expected to be over-sized as it was mentioned earlier. These complications are not present in DPWM, where the control is relatively straightforward and the filter can be designed for 280kHz $>$ 150kHz. From these considerations, the DPWM was selected to be further investigated.

3.3 Rectifier Control for DPWM

In this section the control structure is designed for the Discontinuous PWM. A standard rectifier control with its dq-transformations and Phase Locked Loop (PLL) is adapted to account for the specific three-phase inverting buck-boost converter topology and the selected modulation. The control system of this section is depicted in Fig. 3.4. For convenience purposes, the topology under consideration is again depicted below:

3.3.1 DC-side voltage controller

First, the control system starts with the outermost controller, which is a DC-side voltage regulator. DC-side controller is used to track the reference of the desired DC link voltage. As an output, it provides the required DC link current that, in addition to the DC-side load current measurement, results in a reference for the sum of the DC-side switch current averages $i_{Tdc}^{*}$ . The product of $i_{Tdc}^{*}$ and $V_{dc}^{*}$ , in turn, sets the required power demand of the converter. Assuming that the inner controllers in dq-frame as well as the PLL itself are operating properly and that unity power factor is tracked (which should be true due to time scale separation of the controllers), active power reference can immediately provide the d-component of the AC-side grid current reference in dq-frame through the well-known three-phase active power relation. Given the requirement of unity power factor, q-component reference is set to zero. These dq-components are the final outputs of the outermost DC-side voltage controller.

3.3.2 Grid current controllers in dq-frame

Next, the dq-components of the grid current reference are compared to the grid current measurements. The difference is fed to the second cascaded controllers, responsible for grid current control over the filter inductors in dq-frame. These controllers output the voltage drop required over the filter inductors to draw the required current from the grid. Of course, the resulting dq-components of voltage reference do not carry any information about the CM voltage in converter phases, since dq-transformation does not capture the CM voltage. However, in DPWM we also want to shape the CM voltage as a function of the instantaneous DM voltage references. Therefore to control both DM and CM components of the AC-side capacitor voltages, from here on one has to move back to the abc-frame.

3.3.3 CM voltage and capacitor reference derivation

The dq-abc transformation gives us the respective voltage references across the filter inductors in abc-frame. By adding these voltages to the respective grid voltages, one gets the required AC-side capacitor voltages referenced to the grid star point or, in other words, DM parts of the AC-side capacitor voltage references $V_{Ci,DM}^{*},i\in{a,b,c}$ . In DPWM, the required CM voltage reference $V_{CM}^{*}$ is a function of $V_{Ci,DM}^{*}$ . The relation is as follows (Fig. 2.9):

V_{CM}^{*}=-\underset{i=a,b,c}{max}(V_{Ci,DM}^{*})

(3.1)

From (2.5) and (3.1) the total AC-side voltage references can be derived as a sum of DM and CM references, and yielding one phase with zero voltage reference (clamped):

\begin{split}&V_{Cx}^{*}=V_{Cx,DM}^{*}+V_{CM}^{*}=V_{Cx,DM}^{*}-\underset{i=a,% b,c}{max}(V_{Ci,DM}^{*})=0\\ &V_{Cy}^{*}=V_{Cy,DM}^{*}+V_{CM}^{*}=V_{Cy,DM}^{*}-\underset{i=a,b,c}{max}(V_{% Ci,DM}^{*})\\ &V_{Cz}^{*}=V_{Cz,DM}^{*}+V_{CM}^{*}=V_{Cz,DM}^{*}-\underset{i=a,b,c}{max}(V_{% Ci,DM}^{*})\\ \end{split}

(3.2)

Indeed, from equation (3.1) we know that at any instant in time the CM voltage is equal to the negative DM AC-side capacitor voltage reference of one phase, meaning that the sum of CM and DM references is always equal to zero for one phase. This zero-reference phase changes three times every fundamental period. Thus, for inner controllers instead of any particular phase designator $a,b$ or $c$ , one uses the designators $x,y$ and $z$ , where $x$ always refers to the clamped phase (can be $a,b$ or $c$ at any particular instant). While the phase with $x$ designator is clamped, the references of the remaining phases $y$ and $z$ are fed to the inner controllers, addressed below.

3.3.4 Capacitor AC-side voltage controllers in abc-frame

As it was already said, the phase with $x$ designator is clamped, meaning that its duty cycle is forced to zero and no further calculations are made for this phase. The remaining phase voltages ( $y$ and $z$ designators) are then compared to the respective measurements and the errors are fed to the AC-side voltage controllers - a third stage controllers, responsible for the tracking of the AC-side capacitor voltages. These controllers output the AC capacitor current references. According to KCL (Fig. 3.3) the local average AC-side capacitor current consists of two terms:

i_{Cy,Cz}=C\frac{dV_{Cy,Cz}}{dt}=i_{y,z}+i_{Ty,Tz,avg}

(3.3)

Average buck-boost inductor current, in turn, can be derived from the average AC-side switch current according to the following relation:

\begin{split}&i_{Ly,avg}=\frac{i_{Ty,avg}}{(1-d_{y})}=\Big{(}C\frac{dV_{Cy}}{% dt}-i_{y}\Big{)}\Big{(}1+\frac{|V_{Cy}|}{V_{dc}}\Big{)}\\ &i_{Lz,avg}=\frac{i_{Tz,avg}}{(1-d_{z})}=\Big{(}C\frac{dV_{Cz}}{dt}-i_{z}\Big{% )}\Big{(}1+\frac{|V_{Cz}|}{V_{dc}}\Big{)}\\ \end{split}

(3.4)

From (3.3 - 3.4) table the buck-boost inductor current references are derived:

i_{Ly,avg}^{*}=\frac{i_{Ty,avg}^{*}}{(1-d_{y})}=\Big{(}i_{Cy}^{*}-i_{y}\Big{)}% \Big{(}1+\frac{|V_{Cy}|}{V_{dc}}\Big{)}\text{ }\text{ }\text{ }i_{Lz,avg}^{*}=% \frac{i_{Tz,avg}^{*}}{(1-d_{z})}=\Big{(}i_{Cz}^{*}-i_{z}\Big{)}\Big{(}1+\frac{% |V_{Cz}|}{V_{dc}}\Big{)}

(3.5)

3.3.5 Buck-boost inductor current controllers in abc-frame

Next, buck-boost inductor current references $i_{Ly,avg}^{*}$ and $i_{Lz,avg}^{*}$ are compared to the respective current measurements. The errors are fed to the buck-boost inductor current controllers - a forth stage (innermost, fastest), responsible for the inductor currents of the two active phases. These controllers result in the respective voltage references across the buck-boost inductors $V_{Ly}^{*}$ and $V_{Lz}^{*}$ .

3.3.6 Phase modulators

Finally, from $V_{Ly}^{*}$ and $V_{Lz}^{*}$ the respective duty cycles can be derived through phase modulators. Considering the defined voltage polarities (Fig. 3.3), the modulator equation can be written as:

\begin{split}V_{Ly}&=-V_{dc}d_{y}-V_{Cy}(1-d_{y})\Rightarrow d_{y}=\frac{V_{Ly% }+V_{Cy}}{V_{Cy}-V_{dc}}=\frac{-|V_{Cy}|+V_{Ly}}{-|V_{Cy}|-V_{dc}}=\frac{|V_{% Cy}|-V_{Ly}}{|V_{Cy}|+V_{dc}}\\ V_{Lz}&=-V_{dc}d_{z}-V_{Cz}(1-d_{z})\Rightarrow d_{z}=\frac{V_{Lz}+V_{Cz}}{V_{% Cz}-V_{dc}}=\frac{-|V_{Cz}|+V_{Lz}}{-|V_{Cz}|-V_{dc}}=\frac{|V_{Cz}|-V_{Lz}}{|% V_{Cz}|+V_{dc}}\\ \end{split}

(3.6)

d\geq\text{Carrier}\rightarrow{T_{ac}=0,T_{dc}=1}\text{ }\text{ }\text{ }d<% \text{Carrier}\rightarrow{T_{ac}=1,T_{dc}=0}

(3.7)

From (3.6) the duty cycles of the un-clamped phases can be derived. Summarizing block diagram of the control system is depicted in Fig. 3.4.

3.3.7 Gecko-Simulink results

In Fig. 3.5 one can observe the simulation results of the implemented control system (Fig. 3.4) applied to the three-phase inverting buck-boost converter (Fig. 3.3) with the specifications from Table 3.1. Phase duty cycles, AC-side voltages, grid currents and buck-boost inductor currents are shown in graphs ( $a$ ) to ( $d$ ) respectively. From the graphs one can immediately observe the problem of a high frequency ringing in the clamped phases. Apart from that, a Fourier analysis of the grid currents has shown that the major contribution to the grid current THD comes from the second grid frequency harmonic, indicating potential errors in the grid current controller. Therefore, further measures have to be undertaken to eliminate the ringing at clamping instance and to comply with grid current quality requirements.

3.4 Further Control Improvements

Previous section dealt with the design of a control system for a three-phase inverting buck-boost converter employing DPWM. After applying the designed control in the simulation, the problems of high frequency ringing and grid current quality have been identified. This section addresses some further control improvements needed to ameliorate those.

3.4.1 High frequency ringing and Gecko-Simulink results

Fig. 3.5 reveals that the ringing occurs predominantly in the phase that was just clamped. This ringing is expected, since phase clamping essentially means shorting the AC-side capacitor and the buck-boost inductor. Indeed, consider Fig. 3.3 and the point in time when phase a has just been clamped (this also applies to the other phases as well). The switch $T_{a}$ is permanently turned on, meaning that $C_{a}$ and $L_{a}$ are permanently connected to each other. This configuration can be subject to ringing. Moreover, phase a grid current is also tied to this ringing due to KCL at the node between $T_{a}$ , $C_{a}$ and $L_{fa}$ . Finally, since the grid currents are tied to each other through the grid star point, phase a grid current ringing is translated to the other phases and vice versa, creating the disturbances over those as well (grid currents graph in Fig. 3.5).

From the considerations above it can be deduced that in order to have a smooth clamping transition, one condition needs to be satisfied. The capacitor current $i_{Ca}$ just before the clamping has to be zero in order not to cause a subsequent change of capacitor voltage. This also implies that the grid and buck-boost inductor currents match perfectly just before the clamping. Obviously, this condition cannot be met within the standard DPWM, because in DPWM the capacitor current $i_{Ca}=C\frac{dV_{Ca}}{dt}$ is not zero before clamping (AC-side voltages graph in Fig. 3.5). To resolve this issue, the CM-smoothing is proposed. The idea is to smoothen the sharp edge of the CM voltage (black curve in AC-side voltages graph in Fig. 3.5) in order to provide a smooth transition from one phase clamping to the other. As a result, the capacitor voltages will be reshaped such that $i_{Ca}=C\frac{dV_{Ca}}{dt}\rightarrow 0$ just before the clamping, thus the condition above will be satisfied.

For a CM-smoothing to take place, the control structure in Fig. 3.4 has to be slightly modified. These modifications are depicted in Fig. 3.6 (red highlights). First, the smoothing threshold $V_{var}$ is defined such that the CM voltage near the sharp edge is adapted. In fact, the CM voltage near the sharp edge is just fed forward from the predefined reference shape. This CM feedforward is applied for a short time interval corresponding to the transition from one phase clamping to the other. During this time interval all three phases are operated, which can also be seen from the subsequent control structure in red. Eventually, after the phase clamping transition ends and the CM threshold is deactivated, the control structure returns back to standard DPWM operation. This can also be seen from the $d_{x}$ (0) sign at the output of the modulator, where $d_{x}$ and (0) correspond to the transition and clamped intervals respectively.

Applying the modified control structure in Gecko-Simulink simulation results in a steady state three-phase inverting buck-boost converter waveforms shown in Fig. 3.7. One can immediately see that the high frequency ringing issue has vanished due to CM-smoothing, which results in a smooth transition from one phase clamping to the other. This, however, comes at the price of a short time intervals, where all three phases are operated. Taking into account that mentioned interval is very short, the CM-smoothing algorithm offers a good solution.

Apart from that, as a precaution measure, anti-parallel diodes are connected across the AC-side capacitors. By doing so, one ensures that the AC-side capacitors’ voltages are kept strictly negative in case the CM-smoothing algorithm fails to operate properly. For instance, in case the aforementioned ringing persists around zero after clamping, the transients could result in positive voltages across the AC-side capacitor of the clamped phase. This positive voltage is then discharged over the anti-parallel diode. The resulting topology modification can be seen in Fig. 3.8.

3.5 Rectifier Summary

To sum up, this chapter explored the applicability potential of the three-phase inverting buck-boost converter topology in an EHA rectifier application within the context of a More Electric Aircraft. First, as the rectifier performance heavily depends on the modulation scheme employed, three modulation candidates have been studied and compared with respect to various performance metrics. As a result, Discontinuous PWM (DPWM) has been selected. Note that the modulation analysis and results are topology- rather than application-specific, meaning that DPWM is expected to outperform its counterparts in inverter application as well.

Second, the control structure has been developed for the three-phase inverting buck-boost converter as a rectifier with DPWM. Several arising problems, such as high frequency ringing and grid current quality have been identified and resolved. Some parts of the control structure, for example the inner cascaded controllers and CM voltage derivation, are applicable in the inverter application as well. This is also true for the CM-smoothing algorithm - a major DPWM enabler. In general, when it comes to control, inverter application cases are usually easier than rectifier ones due to the fact that these are usually inherently stable in open-loop. This topology-specific feature of open-loop stability is very useful for hardware commissioning. Theoretical stability analysis and extensive simulations show that three-phase inverting buck-boost converter also possesses open-loop stability in inverter configuration, meaning that with this topology-specific feature the commissioning of a hardware prototype will be much easier.

Overall, rectifier analysis provided a thorough understanding of the topology, its operation and control. Important topology-specific features have been identified.

Chapter 4 Three-Phase Inverting Buck-Boost Converter as a Fuel Cell Powered High-Speed Motor Drive

After finishing the analysis of the three-phase inverting buck-boost converter as a rectifier, this chapter explores a new application, namely a Fuel Cell (FC) powered high-speed motor drive within the context of a Fuel Cell Vehicle (FCV). In section one, a new application and the respective electrical specifications are introduced. Section two deals with the inverter control structure for DPWM. Majority of the results presented in this section are inherited from the rectifier analysis due to latter’s applicability. Next, after defining the application specifications, modulation and control, section three starts the hardware discussion by revealing the selection and design procedures of the main converter power components. Section four addresses secondary components, such as measurements and auxiliary supplies. Printed Circuit Board (PCB) layout design is discussed in section five, which finally leads us to the virtual prototype and its performance in section six.

4.1 Inverter Application and Electrical Specifications

Regarding the application for a Fuel Cell Vehicle (FCV), the authors of [1] briefly explain the operating principle of the FCV and propose the application, where the converters with buck-boost capability could be employed. Fuel Cell Vehicle (FCV) is a vehicle that uses the energy from the chemical reaction in the fuel cell for propulsion. The reaction requires oxygen, which can be extracted from the surrounding air. Thus, there are two distinct motors - main high-power motor for vehicle propulsion and an auxiliary low-power motor that drives the air compressor to sustain the chemical reaction. As it can be seen from Fig. 4.1, the output voltage of the fuel cell heavily depends on the extracted power, which results in a very wide input voltage range for both motor drives. In this context, three-phase inverting buck-boost converter topology could be a good choice for a compressor driver setup (Fig. 4.1). Indeed, compressor driver is a low-power application with a wide input DC voltage range - exactly the niche of the three-phase inverting buck-boost converter. Low number of active components and power conversion within a single stage could become the competitive advantages over conventional counterparts. Moreover, three-phase inverting buck-boost converter provides an inherent filtering of the output AC voltages through its AC-side capacitors, which is good for reducing the high frequency harmonic content and associated losses in the motor of the compressor.

The three-phase inverting buck-boost converter topology and the electrical specifications for an inverter operation within the FCV application are shown in Fig. 4.1 and Table 4.1. Further derivation of the component electrical specifications will be provided in the corresponding sections below.

Table 4.1: Inverter application specifications for a FC powered high-speed motor drive

Parameter	Value	Unit	Param. Explanation (Application)
$P$	$1000$	W	Nominal inverter power rating
$\hat{V}_{o}$	$80$	V	Nominal output AC phase voltage amplitude
$V_{dc}$	$[80-240]$	V	Input DC voltage range
$f_{o}$	$1$	kHz	Nominal output AC frequency

4.2 Inverter Control for DPWM

Regarding the three-phase inverting buck-boost converter control for a motor drive application, a standard inverter control is reviewed and updated to account for the specific converter topology and the selected modulation at hand. For instance, recall the example of a VSI directly connected to Permanent Magnet Synchronous Motor (PMSM). There, the control system comprised two cascaded controllers in a rotor-oriented dq-frame. The outer speed controller provided a reference for a q-component of the stator current, as this q-component is responsible for torque generation. Current dq-component controllers, in turn, provided a references for a dq-components of the inverter AC-side voltages. Since in the example at hand the VSI is directly connected to the PMSM, AC-side voltages can be directly generated through the high-frequency operation of semiconductors. Thus, the voltage reference in dq-frame is translated back to abc-frame and fed to the modulators of the respective phases.

As it can be seen from Fig. 4.1, in considered application one has a three-phase inverting buck-boost converter instead of a VSI directly connected to the PMSM. No explicit filter is placed, thanks to the structure of the three-phase inverting buck-boost converter topology with its AC-side capacitors smoothing the motor voltages and providing inherent filtering. This filtering, however, comes at the price of an additional control effort. Surely, motor nodes $a$ , $b$ and $c$ in Fig. 4.1 are not directly connected to the switched nodes of the three-phase inverting buck-boost converter, as it was the case in the example of VSI. Thus, at least one additional control stage for the AC-side voltages is needed. With this being said and bearing in mind aforementioned discussions on outer speed and motor current controllers, this section addresses only the inner controller stages, specific to the three-phase inverting buck-boost converter. Outer controllers are similar and therefore not addressed here.

When it comes to the inner controller stages, those can be inherited from the rectifier analysis, since the control flow in both cases is the same. Surely, in both cases two outermost controllers provide the AC-side voltage references to be tracked. Since in rectifier case it was done by employing two cascaded controllers for AC-side voltages and buck-boost inductor currents, the same is applicable for inverter. Fig. 4.2 depicts these two cascaded controllers. For details refer to previous chapter.

4.3 Component Selection and Design

This section addresses the selection and design procedures of the main three-phase inverting buck-boost converter components. Given system specifications, relevant for component design, are provided in Table 4.2.

Table 4.2: Given system specifications for the inverter application

Parameter	Value	Unit	Param. Explanation (Given)
$f_{s}$	$300$	kHz	Switching frequency
Device	GaN 600V	-	Semiconductor: Infineon GaN 600V, 55mOhm
No. Dev.	2	-	Number of parallel devices
$\eta$	$>95\%$	-	Minimum efficiency
$\rho$	-	kW/l	Power density as compact as possible

4.3.1 Semiconductors

$\bullet$ Choice of the device

From the Table 4.2 it is known that the switches were predefined for the motor drive application at hand. The selected device is a new generation 600V, 55 mOhm Infineon GaN Gate Injection Transistor (GIT) [13]. Previous works have already studied older generations of GaN devices [14], [15], [16]. As a result of those works, there are several reasons for the selection, which can be generally combined as follows:

$a$ . New GaN 600V devices provide a cost-effective solution in many 400V key applications [14].

$b$ . New GaN 600V devices help increasing the system performance in terms of achievable efficiencies and power density [14].

The application at hand lies exactly in the prescribed voltage vicinity with its maximum required blocking voltage being $V_{dc,max}+2\times\hat{V}_{o}=240\text{V}+2\times 80\text{V}=400$ V.

$\bullet$ Number of parallel devices

Table 4.2 also states that the number of parallel devices equals 2. This decision was influenced by practical concerns. First, the upper limit on the number of parallel devices is set by the size concerns of the half-bridge. Indeed, due to non-zero size of each individual device, using many devices in parallel could increase the gate loop inductance (depending on PCB layout), thus decreasing the switching speed, increasing switching losses or even result in non-symmetric operation of parallel devices. Of course one could suggest increasing the number of separate gate drivers, however, this approach would significantly increase the occupied PCB area, thus compromising the power density, which is set as a primary goal of the prototype. Second, the lower limit on the number of parallel devices is set by the current-carrying capability of one device. From the datasheet [13] it is seen that the maximum pulsed drain-source current is around 60A, while the maximum DC drain-source current is at most 15A, provided that the junction temperature is as low as 25°C. On the other hand, from equations (2.2) and (3.4) one can derive the peak inductor current as a function of input DC voltage and time:

\begin{split}&I_{La,ripple}(V_{dc},t)=\frac{1}{2f_{s}L}\Big{(}\frac{V_{dc}|V_{% Ca}(t)|}{V_{dc}+|V_{Ca}(t)|}\Big{)}\\ &I_{La,avg}(V_{dc},t)=\Big{(}I_{a}(t)+C\frac{dV_{Ca}(t)}{dt}\Big{)}\Big{(}1+% \frac{|V_{Ca}(t)|}{V_{dc}}\Big{)}\\ &I_{La,pk}(V_{dc},t)=\underbrace{\Bigg{[}\underbrace{\frac{1}{2f_{s}L}\Big{(}% \frac{V_{dc}|V_{Ca}(t)|}{V_{dc}+|V_{Ca}(t)|}\Big{)}}_{\text{Inductor current % ripple}}+\underbrace{\Big{(}I_{a}(t)+C\frac{dV_{Ca}(t)}{dt}\Big{)}\Big{(}1+% \frac{|V_{Ca}(t)|}{V_{dc}}\Big{)}}_{\text{Inductor current average}}\Bigg{]}}_% {\text{Inductor current envelope}}\\ \end{split}

(4.1)

After evaluating this equation for DPWM over a fundamental period for various DC voltages, it was observed that $I_{L,pk}$ varies between 25-32A depending on DC voltage. Based on experience with old generation devices this maximum current range was considered too much for a single device, thus the lower limit on the number of parallel devices was selected to be 2. Overall, selecting two parallel devices is well justified.

$\bullet$ Antiparallel diodes

Apart from switches, anti-parallel diodes have to be selected and placed near each individual device. The reason is, as it can be seen from typical reverse characteristics in [13], the internal anti-parallel diode of the switch exhibits a very high reverse drain-source voltage as a function of a negative gate-source voltage, meaning that the device will have significant losses in the reverse conduction mode. This problem has also been mentioned in [16], where the explicit SiC 600V Schottky diode from CREE has been used [17]. Since both voltage and current ratings of this diode comply with application requirements, it will also be used in present work.

$\bullet$ Loss map

Having selected the switches and diodes, their performance needs to be estimated for a subsequent cooling system design. Expected losses can be estimated using a loss map and on-state resistance for soft-switching and hard-switching respectively. While on-state resistance is readily available in the datasheet, the loss map is usually obtained by measuring hard- and soft-switching losses. For the new devices there exists no loss map yet. To overcome this issue, the loss maps from older generation devices with the same ratings will be applied. Assuming that the performance of a new devices is the same or better, a conservative estimation of the semiconductor losses can be obtained. Soft-switching loss map has been measured in [16] using the calorimetric measurement setup. Hard-switching loss map has been measured in [14] using double pulse test. Fig. 4.3 shows the extracted maps. Switched energies are calculated per half-bridge and per transition.

On a separate note, a new measurement board has been designed within the scope of this thesis to measure both hard and soft-switching of the new generation devices. Calorimetric measurement setup was selected due to its higher accuracy. [16] has been used as a main reference. The measurement board is addressed in Appendix A.

$\bullet$ Semiconductor loss evaluation

Using the combined loss map from Fig. 4.3, the electrical specifications and the DPWM waveforms from subsection 2.4.2, the semiconductor losses can be estimated for various inductance values. Indeed, as it was shown in subsection 2.4.2 and in equation (4.1), the buck-boost inductor current waveform (and, consequently, semiconductor losses) depend on the inductance value, therefore the semiconductor losses are estimated as a function of DC voltage for different inductance values (Fig. 4.4).

The nominal output voltage/power of $\hat{V}_{o}=80$ V, $P=1$ kW is assumed. In short, at nominal voltage/power both peak and rms inductor currents $I_{pk}$ and $I_{rms}$ reach their maximum levels and since the very same current flows through the half-bridge, one expects the maximum semiconductor losses as well.

Fig. 4.4a, 4.4b and 4.4c show the semiconductor total, conduction and switching loss components per half-bridge per fundamental period as a function of the DC voltage ranging from 80V to 240V. The considered inductance range is between 6 $\mu$ H and 14 $\mu$ H. The same range will be considered in the subsequent inductor design discussion.

From Fig. 4.4b one can see that the semiconductor conduction losses tend to drop as the DC voltage increases. This can be attributed to the fact that the average inductor current drops as a function of DC voltage, as it is shown in equation (4.1). The drop in conduction losses is not steady though. Moreover, it can be seen that for low inductance values the conduction losses tend to grow again after surpassing some DC voltage. This behavior comes from the non-linear contribution of the inductor ripple current, which is also inversely proportional to the inductance value.

From Fig. 4.4c the first thing to be noticed is that with larger inductance the switching loss tends to grow. This can be explained by the reduced inductor current ripple (equation (4.1)), which is not enough to achieve the switched node current reversal within every switching period to facilitate pure soft-switching. Another thing to be noticed is that with growing DC voltage the switching loss tends to drop first, followed by a steady rise at lower pace. This behavior is expected, since with growing DC voltage the inductor average current decreases and the ripple current increases, meaning that switched node current reversals within every switching period are becoming more frequent. After reaching the DC voltage of predominantly soft-switching, further increase in DC voltage (and current ripple according to (4.1)) results in steady rise of switching losses due to the fact that soft-switching instances occur at higher instantaneous currents and voltages.

4.3.2 Capacitors

$\bullet$ AC-side capacitors

Regarding AC-side capacitors, a standard design constraint applies for those. On one hand, the maximum capacitance value is limited by the reactive power consumption. On the other hand, minimum capacitance value is limited by the AC-side voltage ripple. Assuming that one wants to limit the capacitive current consumption to below 20% of the AC-side load current $\hat{I}_{o}$ , maximum capacitance can be found as follows:

C_{AC,max}=0.2\hat{I}_{o}/\omega_{o}\hat{V}_{o}=3.3\text{ $\mu$F}

(4.2)

Here $\hat{I}_{o}$ and $\hat{V}_{o}$ correspond to phase current and voltage amplitudes with $\hat{I}_{o}=2P/3\hat{V}_{o}=8.33$ A. Using the obtained value of $C_{AC,max}$ in simulations one can observe a voltage ripple within $\pm 3$ %, which is more than enough for the control system to operate properly. Thus, AC-side capacitance was selected to be 3 $\mu$ F. AC-side capacitors were selected to be ceramic (C5750X7T2W105K250KA). In capacitor selection process several factors have been accounted for, including the fact that for X7T ceramics the capacitance drops significantly with applied voltage.

Apart from the output AC-side capacitors, ceramics were also used as commutation capacitors. Higher voltage rating ceramic capacitors were selected for commutation (KTS501B564M55N0T00), as they should withstand $V_{dc}+2\hat{V}_{o}$ , which is greater than $2\hat{V}_{o}$ given for output capacitors.

$\bullet$ DC-side capacitors

Regarding the DC link design, there are not so many explicit requirements for the DC capacitors. In terms of control, extensive simulations and Matlab theoretical calculations show that DC voltage ripple is kept within $\pm 5$ % (which is more than enough for a proper control) already at 30 $\mu$ F of capacitance. This capacitance can be realized using several small electrolytic capacitors for example. Bering in mind these results as well as already available cooling system and inductor designs, the DC link electrolytics are selected to provide as much capacitance as possible while having a good overall converter fill factor.

On the other hand, high-frequency ripple in the electrolytic DC link could become a problem due to high ESR in electrolytics at high frequencies. This problem was alleviated by placing DC ceramic capacitors near the DC-side switches of the phases. By doing so one ensures that high-frequency ripple current of the DC link flows predominantly through these ceramic capacitors that, in turn, have much smaller ESR. There are two reasons behind high frequency current redistribution. First, at high frequencies the impedance of ceramic capacitors is much smaller than that of an ESR-dominated electrolytics. Second, since ceramics are much smaller, they can be placed much nearer to the switches on the PCB, meaning that some additional parasitic inductance between electrolytics and switches (due to longer current path) will further increase the impedance of the electrolytics branch of the DC link. With these, DC link values in the final design are as follows: $6$ x $10$ $\mu$ F of electrolytic capacitors (EKXF251ELL100MJC5S) and $10$ $\mu$ F of ceramic capacitors (C5750X7T2W105K250KA).

4.3.3 Inductor dimensioning point

Regarding the buck-boost inductor, before selection of appropriate inductance value and corresponding design, the dimensioning point within the DC, AC voltage and output power ranges has to be determined, since both inductance sensitivity analysis and design evaluation depend on the operating point. As a good practical rule, the dimensioning point is usually selected based on area product estimation. Two physical limits - core saturation and winding thermal (current density) limit - are accounted for in the area product. Since the inductor core should not saturate and winding should not overheat irrespective of the instantaneous operating point within electrical specifications, the inductor has to be designed for the worst cases both in terms of core and window areas. Consequently, core $A_{c}$ times winding window $A_{w}$ area product $A_{c}A_{w}$ provides a good volume estimation of the prospective inductor that satisfies both saturation and current density limits. Core and winding window ares $A_{c}$ and $A_{w}$ , in turn, depend on peak and rms inductor currents respectively. In short, this dependency can be captured by the following equation:

A_{c}A_{w}\sim LI_{pk}I_{rms}

(4.3)

Bearing in mind the discussion above, inductor dimensioning point can be determined by evaluating $I_{pk}$ and $I_{rms}$ for various DC voltages and for nominal AC-side voltage/power ( $\hat{V}_{o}=80$ V, $P=1$ kW). The reason for nominal AC-side voltage/power consideration can be seen from equation (4.1). For instance, in equation (4.1) if one analyzes $I_{La,pk}$ as a function of AC-side voltage $V_{Ca}$ and current $I_{a}$ (proportional to power), one observes that these parameters are in direct relation, meaning that with increasing $V_{Ca}$ and $I_{a}$ the $I_{La,pk}$ only increases. The same holds true for $I_{La,rms}$ . Thus, maximum current product $I_{pk}I_{rms}$ and, consequently, maximum area product $A_{c}A_{w}$ occurs at nominal AC-side voltage/power. The same cannot be said about DC voltage relation, since with increasing DC voltage the inductor current ripple term increases, while the average term decreases (4.1).