-
1-bit raw voltage recording system for dedicated observations of transients at low radio frequencies
Authors:
Kshitij S. Bane,
Indrajit V. Barve,
G. V. S. Gireesh,
C. Kathiravan,
R. Ramesh
Abstract:
Recently we had reported commissioning of a prototype for pulsar observations at low radio frequencies (<100 MHz) using log-periodic dipole antennas (LPDAs) in the Gauribidanur Radio Observatory near Bangalore in India. The aforementioned system (GAuribidanur Pulsar System, GAPS) is currently being augmented to directly digitize the radio frequency signals from the individual antennas in the array…
▽ More
Recently we had reported commissioning of a prototype for pulsar observations at low radio frequencies (<100 MHz) using log-periodic dipole antennas (LPDAs) in the Gauribidanur Radio Observatory near Bangalore in India. The aforementioned system (GAuribidanur Pulsar System, GAPS) is currently being augmented to directly digitize the radio frequency signals from the individual antennas in the array. Our initial results using 1-bit raw voltage recording system indicates that such a back-end receiver offers distinct advantages like, (i) simultaneous observations of any set of desired directions in the sky with multiple offline beams and smaller data rate/volume, (ii) archival of the observed data with minimal resources for re-analysis in the future, either in the same or different set of directions in the sky.
△ Less
Submitted 23 April, 2024;
originally announced April 2024.
-
Potential-well bunch lengthening in electron storage rings
Authors:
Demin Zhou,
Gaku Mitsuka,
Takuya Ishibashi,
Karl Bane
Abstract:
The cubic equation derived by B. Zotter has been popularly used for electron storage rings to describe the scaling law of potential-well bunch lengthening. This equation has also often been used to calculate the effective impedance when the bunch lengthening is measured or simulated. This paper discusses the validity of Zotter's equation and presents an alternative but self-consistent equation for…
▽ More
The cubic equation derived by B. Zotter has been popularly used for electron storage rings to describe the scaling law of potential-well bunch lengthening. This equation has also often been used to calculate the effective impedance when the bunch lengthening is measured or simulated. This paper discusses the validity of Zotter's equation and presents an alternative but self-consistent equation for potential-well bunch lengthening. Its applications to predicting bunch lengthening and extracting effective impedance from bunch length measurements are also addressed.
△ Less
Submitted 1 September, 2023;
originally announced September 2023.
-
Theories derived from Haissinski equation and their applications to electron storage rings
Authors:
Demin Zhou,
Takuya Ishibashi,
Gaku Mitsuka,
Makoto Tobiyama,
Karl Bane,
Linhao Zhang
Abstract:
As a stationary solution of the Vlasov-Fokker-Planck equation, the Haissinski equation predicts the equilibrium line density of a bunch that circulates in a storage ring for a given wake function. This paper shows that some equations regarding the centroid shift of the bunch, the peak position of the bunch profile, bunch length, and extraction of impedance from the bunch profile can be derived fro…
▽ More
As a stationary solution of the Vlasov-Fokker-Planck equation, the Haissinski equation predicts the equilibrium line density of a bunch that circulates in a storage ring for a given wake function. This paper shows that some equations regarding the centroid shift of the bunch, the peak position of the bunch profile, bunch length, and extraction of impedance from the bunch profile can be derived from the Haissinski equation in a self-consistent manner. In particular, a generalized quadratic equation for potential-well bunch lengthening is obtained to accommodate any absolute impedance model, expanding upon Zotter's cubic equation, which is primarily applicable to inductive impedance. The equations derived in this paper are tested using computed impedance models for some electron storage rings, showing machine-dependent properties of impedance effects. We conclude that these equations can be employed in electron storage rings to effectively bridge the gap between impedance computations and beam-based measurements.
△ Less
Submitted 20 December, 2023; v1 submitted 3 July, 2023;
originally announced July 2023.
-
A prototype for pulsar observations at low radio frequencies using log periodic dipole antennas
Authors:
Kshitij S. Bane,
Indrajit V. Barve,
G. V. S. Gireesh,
C. Kathiravan,
R. Ramesh
Abstract:
A prototype for dedicated observations of pulsars and other astrophysical transients in the frequency range 50\,-\,80\,MHz has been recently commissioned at the Gauribidanur radio observatory near Bangalore in India. The antenna set-up, analog \& digital receiver systems, and the initial observations are presented.
A prototype for dedicated observations of pulsars and other astrophysical transients in the frequency range 50\,-\,80\,MHz has been recently commissioned at the Gauribidanur radio observatory near Bangalore in India. The antenna set-up, analog \& digital receiver systems, and the initial observations are presented.
△ Less
Submitted 11 February, 2022;
originally announced February 2022.
-
Field Analysis for a Highly-Overmoded Iris Line, with Application to THz Radiation Transport at LCLS
Authors:
Adham Naji,
Gennady Stupakov,
Zhirong Huang,
Karl Bane
Abstract:
Vector field analysis is presented for a highly overmoded iris-line structure that can act as a medium of transportation for THz radiation. The axisymmetric structure is capable of supporting hybrid modes with desirable features such as low propagation loss, uniformly linear polarization and approximately-Gaussian intensity profile across the iris. A specific application that can benefit from thes…
▽ More
Vector field analysis is presented for a highly overmoded iris-line structure that can act as a medium of transportation for THz radiation. The axisymmetric structure is capable of supporting hybrid modes with desirable features such as low propagation loss, uniformly linear polarization and approximately-Gaussian intensity profile across the iris. A specific application that can benefit from these features is the transportation of THz undulator radiation over hundreds of meters to reach the experimental halls at the LCLS facility, SLAC, Stanford. Such a structure has been modelled before as a boundary-value problem using Vainstein's impedance boundary condition and assuming infinitely-thin screens. Given that physical realizations of such screens must have finite thickness and that the THz wavelength in the 3-15 THz range is expected to be smaller than convenient screen thicknesses in practice, the question of the impact of finite screen thickness on propagation performance becomes rather pressing. To address this question, we present a mode-matching analysis of the structure, with finite screen thickness and perturbatively clustered (localized) field expansions, for computational feasibility. The effect of screen thickness is seen to lower the attenuation constant on the iris line, which is dominated by diffraction loss. The propagation loss predictions based on the Vainstein-model are compared with the numerical results from mode-matching for infinitely-thin screens, where the former method is observed to agree with the numerical results better at higher Fresnel numbers (highly-overmoded structures). The properties of the dominant mode fields are formally derived from first principles and a recommended approach is discussed for the inclusion of screen-thickness effects into propagation loss estimations.
△ Less
Submitted 16 December, 2021;
originally announced December 2021.
-
Octupole based current horn suppresion in multi-stage bunch compression with emittance growth correction
Authors:
Nicholas Sudar,
Yuantao Ding,
Yuri Nosochkov,
Karl Bane,
Zhen Zhang
Abstract:
High brightness linear accelerators typically produce electron beams with peaks in the head and/or tail of the current profile. These current horns are formed after bunch compression due to non-linear correlations in the longitudinal phase space and the higher order optics of the compressor. It has been suggested that this higher order compression can be corrected by inserting an octupole magnet n…
▽ More
High brightness linear accelerators typically produce electron beams with peaks in the head and/or tail of the current profile. These current horns are formed after bunch compression due to non-linear correlations in the longitudinal phase space and the higher order optics of the compressor. It has been suggested that this higher order compression can be corrected by inserting an octupole magnet near the center of a bunch compressor. However, this scheme provides a correlated transverse kick leading to growth of the projected emittance. We present here a method whereby octupole magnets are inserted into two sequential bunch compressors. By tuning a $π$ betatron phase advance between the two octupoles, the correlated transverse kick from the first octupole can be corrected by the second, while providing a cummulative adjustment of the higher order compression.
△ Less
Submitted 4 September, 2020;
originally announced September 2020.
-
Improved Numerical Method for Solution of the Haïssinski Equation
Authors:
Robert Warnock,
Karl Bane
Abstract:
The longitudinal charge density of an electron beam in its equilibrium state is given by the solution of the Haïssinski equation, which provides a stationary solution of the Vlasov-Fokker-Planck equation. The physical input is the longitudinal wake potential. We formulate the Haïssinski equation as a nonlinear integral equation with the normalization integral stated as a functional of the solution…
▽ More
The longitudinal charge density of an electron beam in its equilibrium state is given by the solution of the Haïssinski equation, which provides a stationary solution of the Vlasov-Fokker-Planck equation. The physical input is the longitudinal wake potential. We formulate the Haïssinski equation as a nonlinear integral equation with the normalization integral stated as a functional of the solution. This equation can be solved in a simple way by the matrix version of Newtons's iteration, beginning with the Gaussian as a first guess. We illustrate for several quasi-realistic wake potentials. Convergence is extremely robust, even at currents much higher than nominal for the storage rings considered. The method overcomes limitations of earlier procedures, and provides the convenience of automatic normalization of the solution.
△ Less
Submitted 3 August, 2018;
originally announced August 2018.
-
An Advanced NCRF Linac Concept for a High Energy e$^+$e$^-$ Linear Collider
Authors:
Karl L. Bane,
Timothy L. Barklow,
Martin Breidenbach,
Craig P. Burkhart,
Eric A. Fauve,
Alysson R. Gold,
Vincent Heloin,
Zenghai Li,
Emilio A. Nanni,
Mamdouh Nasr,
Marco Oriunno,
James McEwan Paterson,
Michael E. Peskin,
Tor O. Raubenheimer,
Sami G. Tantawi
Abstract:
We have explored a concept for an advanced Normal-Conducting Radio-Frequency (NCRF) C-band linear accelerator (linac) structure to achieve a high gradient, high power e$^+$e$^-$ linear collider in the TeV class. This design study represents the first comprehensive investigation for an emerging class of distributed coupling accelerator topology exploring nominal cavity geometries, frequency and tem…
▽ More
We have explored a concept for an advanced Normal-Conducting Radio-Frequency (NCRF) C-band linear accelerator (linac) structure to achieve a high gradient, high power e$^+$e$^-$ linear collider in the TeV class. This design study represents the first comprehensive investigation for an emerging class of distributed coupling accelerator topology exploring nominal cavity geometries, frequency and temperature of operation. The structure features internal manifolds for distributing RF power separately to each cell, permitting the full structure geometry to be designed for high shunt impedance and low breakdown. Optimized within operational constraints, we find that it is advantageous for the structure to be cooled directly by liquid nitrogen (LN), further increasing the shunt impedance. A crucial part of this design process has been cost optimization, which is largely driven by the cost of peak RF power. The first operation of a distributed coupling structure at cryogenic temperatures and the nominal operating gradient 120 MeV/m is also presented, demonstrating the feasibility of achieving high-gradient performance with a cryogenically-cooled normal-conducting accelerating structure.
△ Less
Submitted 7 April, 2019; v1 submitted 26 July, 2018;
originally announced July 2018.
-
Wake Measurements of a Dechirper Jaw with Non-Zero Tilt Angle
Authors:
Karl Bane,
Marc Guetg,
Alberto Lutman
Abstract:
The RadiaBeam/SLAC dechirper at the Linac Coherent Light Source (LCLS) is being used as a fast kicker, by inducing transverse wakefields, to e.g. facilitate Fresh-slice, two-color laser operation. The dechirper jaws are independently adjustable at both ends, and it is difficult to avoid leaving residual (longitudinal) tilt in them during set-up. In this report we develop a model independent method…
▽ More
The RadiaBeam/SLAC dechirper at the Linac Coherent Light Source (LCLS) is being used as a fast kicker, by inducing transverse wakefields, to e.g. facilitate Fresh-slice, two-color laser operation. The dechirper jaws are independently adjustable at both ends, and it is difficult to avoid leaving residual (longitudinal) tilt in them during set-up. In this report we develop a model independent method of removing unknown tilt in a jaw. In addition, for a short uniform bunch passing by a single dechirper plate, we derive an explicit analytical formula for the transverse wake kick as function of average plate offset and tilt angle. We perform wake kick measurements for the different dechirper jaws of the RadiaBeam/SLAC dechirper, and find that the agreement between measurement and theory is excellent.
△ Less
Submitted 9 January, 2018; v1 submitted 8 January, 2018;
originally announced January 2018.
-
The Impedance of Flat Metallic Plates with Small Corrugations
Authors:
Karl Bane
Abstract:
Summarizes recent work on the wakefields and impedances of flat, metallic plates with small corrugations
Summarizes recent work on the wakefields and impedances of flat, metallic plates with small corrugations
△ Less
Submitted 8 November, 2017;
originally announced November 2017.
-
Measurements of wake-induced electron beam deflection in a dechirper at the Linac Coherent Light Source
Authors:
Johann Zemella,
Karl Bane,
Alan Fisher,
Marc Guetg,
Zhirong Huang,
Richard Iverson,
Patrick Krejcik,
Alberto Lutman,
Timothy Maxwell,
Alexander Novokhatski,
Gennady Stupakov,
Zhen Zhang,
Mark Harrison,
Marcos Ruelas
Abstract:
The RadiaBeam/SLAC dechirper, a structure consisting of pairs of flat, metallic, corrugated plates, %a corrugated structure in flat geometry, has been installed just upstream of the undulators in the Linac Coherent Light Source (LCLS). As a dechirper, with the beam passing between the plates on axis, longitudinal wakefields are induced that can remove unwanted energy chirp in the beam. However, wi…
▽ More
The RadiaBeam/SLAC dechirper, a structure consisting of pairs of flat, metallic, corrugated plates, %a corrugated structure in flat geometry, has been installed just upstream of the undulators in the Linac Coherent Light Source (LCLS). As a dechirper, with the beam passing between the plates on axis, longitudinal wakefields are induced that can remove unwanted energy chirp in the beam. However, with the beam passing off axis, strong transverse wakes are also induced. This mode of operation has already been used for the production of intense, multi-color photon beams using the Fresh-Slice technique, and is being used to develop a diagnostic for attosecond bunch length measurements. Here we measure, as function of offset, the strength of the transverse wakefields that are excited between the two plates, and also for the case of the beam passing near to a single plate. We compare with analytical formulas from the literature, and find good agreement. This report presents the first systematic measurements of the transverse wake strength in a dechirper, one that has been excited by a bunch with the short pulse duration and high energy found in an X-ray free electron laser.
△ Less
Submitted 2 August, 2017;
originally announced August 2017.
-
Estimate of Joule Heating in a Flat Dechirper
Authors:
Karl Bane,
Gennady Stupakov,
Erion Gjonaj
Abstract:
We have performed Joule power loss calculations for a flat dechirper. We have considered the configurations of the beam on-axis between the two plates---for chirp control---and for the beam especially close to one plate---for use as a fast kicker. Our calculations use a surface impedance approach, one that is valid when corrugation parameters are small compared to aperture (the perturbative parame…
▽ More
We have performed Joule power loss calculations for a flat dechirper. We have considered the configurations of the beam on-axis between the two plates---for chirp control---and for the beam especially close to one plate---for use as a fast kicker. Our calculations use a surface impedance approach, one that is valid when corrugation parameters are small compared to aperture (the perturbative parameter regime). In our model we ignore effects of field reflections at the sides of the dechirper plates, and thus expect the results to underestimate the Joule losses. The analytical results were also tested by numerical, time-domain simulations. We find that most of the wake power lost by the beam is radiated out to the sides of the plates. For the case of the beam passing by a single plate, we derive an analytical expression for the broad-band impedance, and---in Appendix B---numerically confirm recently developed, analytical formulas for the short-range wakes. While our theory can be applied to the LCLS-II dechirper with large gaps, for the nominal apertures we are not in the perturbative regime and the reflection contribution to Joule losses is not negligible. With input from computer simulations, we estimate the Joule power loss (assuming bunch charge of 300 pC, repetition rate of 100 kHz) is 21~W/m for the case of two plates, and 24 W/m for the case of a single plate.
△ Less
Submitted 6 February, 2017;
originally announced February 2017.
-
Wakefields of a Beam near a Single Plate in a Flat Dechirper
Authors:
Karl Bane,
Gennady Stupakov,
Igor Zagorodnov
Abstract:
We give formulas for the longitudinal, transverse, and quad point charge wakes for a short bunch of electrons passing by one plate of a flat dechirper.
We give formulas for the longitudinal, transverse, and quad point charge wakes for a short bunch of electrons passing by one plate of a flat dechirper.
△ Less
Submitted 28 November, 2016;
originally announced November 2016.
-
Longitudinal Stability Study for the FACET-II e+ Damping Ring
Authors:
Karl Bane
Abstract:
This is an initial study of the longitudinal, single-bunch stability in the proposed FACET-II e+ damping ring. It is preliminary because many vacuum chamber objects of the ring have not yet been designed.
This is an initial study of the longitudinal, single-bunch stability in the proposed FACET-II e+ damping ring. It is preliminary because many vacuum chamber objects of the ring have not yet been designed.
△ Less
Submitted 23 November, 2016;
originally announced November 2016.
-
Measurements of Terahertz Radiation Generated using a Metallic, Corrugated Pipe
Authors:
Karl Bane,
Gennady Stupakov,
Sergey Antipov,
Mikhail Fedurin,
Karl Kusche,
Christina Swinson,
Dao Xiang
Abstract:
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-p…
▽ More
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-peak) of 60 um. In the experiment we measured both the effect on the beam of the structure wakefield and the spectral properties of the radiation excited by the beam. We began by injecting a relatively long beam compared to the wavelength of the radiation, but with short rise time, to excite the structure, and then used a downstream spectrometer to infer the radiation wavelength. This was followed by injecting a shorter bunch, and then using an interferometer (also downstream of the corrugated pipe) to measure the spectrum of the induced THz radiation. For the THz pulse we obtain and compare with calculations: the central frequency, the bandwidth, and the spectral power---compared to a diffraction radiation background signal.
△ Less
Submitted 22 August, 2016;
originally announced August 2016.
-
Measurements of Terahertz Generation in a Metallic, Corrugated Beam Pipe
Authors:
K. L. F. Bane,
S. Antipov,
M. Fedurin,
K. Kusche,
C. Swinson,
D. Xiang
Abstract:
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-p…
▽ More
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-peak) of 60 um. In the experiment we measured both the effect on the beam of the structure wakefield and the spectral properties of the radiation excited by the beam. We began by injecting a relatively long beam compared to the wavelength of the radiation to excite the structure, and then used a downstream spectrometer to infer the radiation wavelength. This was followed by injecting a shorter bunch, and then using an interferometer (also downstream of the corrugated pipe) to measure the spectrum of the induced THz radiation.
△ Less
Submitted 6 June, 2016;
originally announced June 2016.
-
Analytical Formulas for Short Bunch Wakes in a Flat Dechirper
Authors:
K. Bane,
G. Stupakov,
I. Zagorodnov
Abstract:
We develop analytical models of the longitudinal and transverse wakes, on and off axis for realistic structures, and then compare them with numerical calculations, and generally find good agreement. These analytical "first order" formulas approximate the droop at the origin of the longitudinal wake and of the slope of the transverse wakes; they represent an improvement in accuracy over earlier, "z…
▽ More
We develop analytical models of the longitudinal and transverse wakes, on and off axis for realistic structures, and then compare them with numerical calculations, and generally find good agreement. These analytical "first order" formulas approximate the droop at the origin of the longitudinal wake and of the slope of the transverse wakes; they represent an improvement in accuracy over earlier, "zeroth order" formulas. In example calculations for the RadiaBeam/LCLS dechirper using typical parameters, we find a 16\% droop in the energy chirp at the bunch tail compared to simpler calculations. With the beam moved to 200~$μ$m from one jaw in one dechiper section, one can achieve a 3~MV transverse kick differential over a 30~$μ$m length.
△ Less
Submitted 23 March, 2016;
originally announced March 2016.
-
Dechirper Wakefields for Short Bunches
Authors:
Karl Bane,
Gennady Stupakov
Abstract:
In previous work [1] general expressions, valid for arbitrary bunch lengths, were derived for the wakefields of corrugated structures with flat geometry, such as is used in the RadiaBeam/LCLS dechirper. However, the bunch at the end of linac-based X-ray FELs--like the LCLS--is extremely short, and for short bunches the wakes can be considerably simplified. In this work, we first derive analytical…
▽ More
In previous work [1] general expressions, valid for arbitrary bunch lengths, were derived for the wakefields of corrugated structures with flat geometry, such as is used in the RadiaBeam/LCLS dechirper. However, the bunch at the end of linac-based X-ray FELs--like the LCLS--is extremely short, and for short bunches the wakes can be considerably simplified. In this work, we first derive analytical approximations to the short-range wakes. These are generalized wakes, in the sense that their validity is not limited to a small neighborhood of the symmetry axis, but rather extends to arbitrary transverse offsets of driving and test particles. The validity of these short-bunch wakes holds not only for the corrugated structure, but rather for any flat structure whose beam-cavity interaction can be described by a surface impedance. We use these wakes to obtain, for a short bunch passing through a dechirper: estimates of the energy loss as function of gap, the transverse kick as function of beam offset, the slice energy spread increase, and the emittance growth. In the Appendix, a more accurate derivation--than is found in [1]--of the arbitrary bunch length wakes is performed; we find full agreement with the earlier results, provided the bunches are short compared to the dechirper gap, which is normally the regime of interest.
[1] K. Bane and G. Stupakov, Phys. Rev. ST Accel. Beams 18, 034401(2015).
△ Less
Submitted 22 March, 2016; v1 submitted 26 January, 2016;
originally announced January 2016.
-
Calculation of wakefields in 2D rectangular structures
Authors:
I. Zagorodnov,
K. L. F Bane,
G. Stupakov
Abstract:
We consider the calculation of electromagnetic fields generated by an electron bunch passing through a vacuum chamber structure that, in general, consists of an entry pipe, followed by some kind of transition or cavity, and ending in an exit pipe. We limit our study to structures having rectangular cross-section, where the height can vary as function of longitudinal coordinate but the width and si…
▽ More
We consider the calculation of electromagnetic fields generated by an electron bunch passing through a vacuum chamber structure that, in general, consists of an entry pipe, followed by some kind of transition or cavity, and ending in an exit pipe. We limit our study to structures having rectangular cross-section, where the height can vary as function of longitudinal coordinate but the width and side walls remain fixed. For such structures, we derive a Fourier representation of the wake potentials through one-dimensional functions. A new numerical approach for calculating the wakes in such structures is proposed and implemented in the computer code ECHO(2D). The computation resource requirements for this approach are moderate and comparable to those for finding the wakes in 2D rotationally symmetric structures. Numerical examples obtained with the new numerical code are presented.
△ Less
Submitted 31 August, 2015; v1 submitted 31 July, 2015;
originally announced August 2015.
-
Wakefield effects of the bypass line in LCLS-II
Authors:
K. Bane,
T. Raubenheimer
Abstract:
In LCLS-II, after acceleration and compression and just before entering the undulator, the beam passes through 2.5 km of 24.5 mm (radius) stainless steel pipe. The bunch that passes through the pipe is extremely short---with an rms of 8 um for the nominal 100 pC case. Thus, even though the pipe has a large aperture, the wake that applies is the {\it short-range} resistive wall wakefield. The bunch…
▽ More
In LCLS-II, after acceleration and compression and just before entering the undulator, the beam passes through 2.5 km of 24.5 mm (radius) stainless steel pipe. The bunch that passes through the pipe is extremely short---with an rms of 8 um for the nominal 100 pC case. Thus, even though the pipe has a large aperture, the wake that applies is the {\it short-range} resistive wall wakefield. The bunch distribution is approximately uniform, and therefore the wake induced voltage is characterized by a rather linear voltage chirp. It turns out that the wake supplies needed dechirping to the LCLS-II beam before it enters the undulator. In this note we calculate the wake, discuss the confidence in the calculation, and investigate how to improve the induced chirp linearity and/or strength. Finally, we also study the strength and effects of the transverse (dipole) resistive wall wakefield.
△ Less
Submitted 6 November, 2014;
originally announced November 2014.
-
Untrapped HOM Radiation Absorption in the LCLS-II Cryomodules
Authors:
K. Bane,
C. Nantista,
C. Adolphsen,
T. Raubenheimer,
A. Saini,
N. Solyak,
V. Yakovlev
Abstract:
The superconducting cavities in the continuous wave (CW) linacs of LCLS-II are designed to operate at 2 K, where cooling costs are very expensive. One source of heat is presented by the higher order mode (HOM) power deposited by the beam. Due to the very short bunch length--especially in L3 the final linac--the LCLS-II beam spectrum extends into the terahertz range. Ceramic absorbers, at 70 K and…
▽ More
The superconducting cavities in the continuous wave (CW) linacs of LCLS-II are designed to operate at 2 K, where cooling costs are very expensive. One source of heat is presented by the higher order mode (HOM) power deposited by the beam. Due to the very short bunch length--especially in L3 the final linac--the LCLS-II beam spectrum extends into the terahertz range. Ceramic absorbers, at 70 K and located between cryomodules, are meant to absorb much of this power. In this report we perform two kinds of calculations to estimate the effectiveness of the absorbers and the amount of beam power that needs to be removed at 2 K.
△ Less
Submitted 5 November, 2014;
originally announced November 2014.
-
Roughness Tolerance Studies for the Undulator Beam Pipe Chamber of LCLS-II
Authors:
K. Bane,
G. Stupakov
Abstract:
We investigate the effect of wall roughness on the wakefield-induced energy variation in the undulator beam pipe of LCLS-II. We find that a wall roughness equivalent to an rms surface slope of 30 mr increases the total induced energy variation within the bunch (due to the resistive wall wake) by a modest 20%.
We investigate the effect of wall roughness on the wakefield-induced energy variation in the undulator beam pipe of LCLS-II. We find that a wall roughness equivalent to an rms surface slope of 30 mr increases the total induced energy variation within the bunch (due to the resistive wall wake) by a modest 20%.
△ Less
Submitted 1 May, 2014;
originally announced May 2014.
-
Some wakefield effects in the superconducting RF cavities of LCLS-II
Authors:
K. Bane,
A. Romanenko,
V. Yakovlev
Abstract:
For LCLS-II we estimate the power of radiated wakefields generated in the SRF cavities (including the 3rd harmonic cavities) and in the end transitions. Much of this power will pass through and reflect in the strings of cryomodules that comprise linacs L1, L2, or L3. Presumably, some of it will be absorbed by the higher order mode (HOM) couplers, or by the absorbers at warmer temperatures situated…
▽ More
For LCLS-II we estimate the power of radiated wakefields generated in the SRF cavities (including the 3rd harmonic cavities) and in the end transitions. Much of this power will pass through and reflect in the strings of cryomodules that comprise linacs L1, L2, or L3. Presumably, some of it will be absorbed by the higher order mode (HOM) couplers, or by the absorbers at warmer temperatures situated between the cryomodules. We investigate where such power gets generated, but not where it ends up. As such the results can serve as a pessimistic calculation of the extra power that needs to be removed by the cryosystem. Finally, we also estimate---under the assumption that all the wake power ends up in the SRF walls---the wall heating and the extent of Cooper pair breaking in L3, where the bunch is most intense. Note that all calculations here are of single bunch effects; thus resonant interactions are not included.
△ Less
Submitted 27 March, 2014;
originally announced March 2014.
-
Impedance Calculations of Non-Axisymmetric Transitions Using the Optical Approximation
Authors:
K. L. F. Bane,
G. Stupakov,
I. Zagorodnov
Abstract:
In a companion report, we have derived a method for finding the impedance at high frequencies of vacuum chamber transitions that are short compared to the catch-up distance, in a frequency regime that (in analogy to geometric optics for light) we call the optical regime. In this report we apply the method to various non-axisymmetric geometries such as irises/short collimators in a beam pipe, ste…
▽ More
In a companion report, we have derived a method for finding the impedance at high frequencies of vacuum chamber transitions that are short compared to the catch-up distance, in a frequency regime that (in analogy to geometric optics for light) we call the optical regime. In this report we apply the method to various non-axisymmetric geometries such as irises/short collimators in a beam pipe, step-in transitions, step-out transitions, and more complicated transitions of practical importance. Most of our results are analytical, with a few given in terms of a simple one dimensional integral. Our results are compared to wakefield simulations with the time-domain, finite-difference program ECHO, and excellent agreement is found.
△ Less
Submitted 19 March, 2007;
originally announced March 2007.
-
Optical approximation in the theory of geometric impedance
Authors:
G. Stupakov,
K. L. F. Bane,
I. Zagorodnov
Abstract:
In this paper we introduce an optical approximation into the theory of impedance calculation, one valid in the limit of high frequencies. This approximation neglects diffraction effects in the radiation process, and is conceptually equivalent to the approximation of geometric optics in electromagnetic theory. Using this approximation, we derive equations for the longitudinal impedance for arbitr…
▽ More
In this paper we introduce an optical approximation into the theory of impedance calculation, one valid in the limit of high frequencies. This approximation neglects diffraction effects in the radiation process, and is conceptually equivalent to the approximation of geometric optics in electromagnetic theory. Using this approximation, we derive equations for the longitudinal impedance for arbitrary offsets, with respect to a reference orbit, of source and test particles. With the help of the Panofsky-Wenzel theorem we also obtain expressions for the transverse impedance (also for arbitrary offsets). We further simplify these expressions for the case of the small offsets that are typical for practical applications. Our final expressions for the impedance, in the general case, involve two dimensional integrals over various cross-sections of the transition. We further demonstrate, for several known axisymmetric examples, how our method is applied to the calculation of impedances. Finally, we discuss the accuracy of the optical approximation and its relation to the diffraction regime in the theory of impedance.
△ Less
Submitted 16 March, 2007;
originally announced March 2007.
-
Impedance of a Rectangular Beam Tube with Small Corrugations
Authors:
K. L. F. Bane,
G. Stupakov
Abstract:
We consider the impedance of a structure with rectangular, periodic corrugations on two opposing sides of a rectangular beam tube. Using the method of field matching, we find the modes in such a structure. We then limit ourselves to the the case of small corrugations, but where the depth of corrugation is not small compared to the period. For such a structure we generate analytical approximate s…
▽ More
We consider the impedance of a structure with rectangular, periodic corrugations on two opposing sides of a rectangular beam tube. Using the method of field matching, we find the modes in such a structure. We then limit ourselves to the the case of small corrugations, but where the depth of corrugation is not small compared to the period. For such a structure we generate analytical approximate solutions for the wave number $k$, group velocity $v_g$, and loss factor $κ$ for the lowest (the dominant) mode which, when compared with the results of the complete numerical solution, agreed well. We find: if $w\sim a$, where $w$ is the beam pipe width and $a$ is the beam pipe half-height, then one mode dominates the impedance, with $k\sim1/\sqrt{wδ}$ ($δ$ is the depth of corrugation), $(1-v_g/c)\simδ$, and $κ\sim1/(aw)$, which (when replacing $w$ by $a$) is the same scaling as was found for small corrugations in a {\it round} beam pipe. Our results disagree in an important way with a recent paper of Mostacci {\it et al.} [A. Mostacci {\it et al.}, Phys. Rev. ST-AB, {\bf 5}, 044401 (2002)], where, for the rectangular structure, the authors obtained a synchronous mode with the same frequency $k$, but with $κ\simδ$. Finally, we find that if $w$ is large compared to $a$ then many nearby modes contribute to the impedance, resulting in a wakefield that Landau damps.
△ Less
Submitted 10 September, 2002;
originally announced September 2002.
-
Wakefield Band Partitioning In Linac Structures
Authors:
R. M. Jones,
V. Dolgashev,
K. L. F. Bane,
E. Lin
Abstract:
In the NLC project multiple bunches of electrons and positrons will be accelerated initially to a centre of mass of 500 GeV and later to 1 TeV or more. In the process of accelerating 192 bunches within a pulse train, wakefields are excited which kick the trailing bunches off axis and can cause luminosity dilution and BBU (Beam Break Up). Several structures to damp the wakefield have been designe…
▽ More
In the NLC project multiple bunches of electrons and positrons will be accelerated initially to a centre of mass of 500 GeV and later to 1 TeV or more. In the process of accelerating 192 bunches within a pulse train, wakefields are excited which kick the trailing bunches off axis and can cause luminosity dilution and BBU (Beam Break Up). Several structures to damp the wakefield have been designed and tested at SLAC and KEK and these have been found to successfully damp the wakefield [1]. However, these 2pi/3 structures suffered from electrical breakdown and this has prompted us to explore lower group velocity structures operating at higher fundamental mode phase advances. The wakefield partitioning amongst the bands has been found to change markedly with increased phase advance. Here we report on general trends in the kick factor and associated wakefield band partitioning in dipole bands as a function of phase advance of the synchronous mode in linacs. These results are applicable to both TW (travelling wave) and SW (standing wave) structures [1] R.M. Jones et al, PAC99, also SLAC-PUB-8103
△ Less
Submitted 23 August, 2002;
originally announced August 2002.
-
Intrabeam scattering analysis of measurements at KEK's ATF damping ring
Authors:
K. L. F. Bane,
H. Hayano,
K. Kubo,
T. Naito,
T. Okugi,
J. Urakawa
Abstract:
We derive a simple relation for estimating the relative emittance growth in x and y due to intrabeam scattering (IBS) in electron storage rings. We show that IBS calculations for the ATF damping ring, when using the formalism of Bjorken-Mtingwa, a modified formalism of Piwinski (where eta squared divided by beta has been replaced by the dispersion invariant), or a simple high-energy approximate…
▽ More
We derive a simple relation for estimating the relative emittance growth in x and y due to intrabeam scattering (IBS) in electron storage rings. We show that IBS calculations for the ATF damping ring, when using the formalism of Bjorken-Mtingwa, a modified formalism of Piwinski (where eta squared divided by beta has been replaced by the dispersion invariant), or a simple high-energy approximate formula all give results that agree well. Comparing theory, including the effect of potential well bunch lengthening, with a complete set of ATF steady-state beam size vs. current measurements we find reasonably good agreement for energy spread and horizontal emittance. The measured vertical emittance, however, is larger than theory in both offset (zero current emittance) and slope (emittance change with current). The slope error indicates measurement error and/or additional current-dependent physics at the ATF; the offset error, that the assumed Coulomb log is correct to within a factor of 1.75.
△ Less
Submitted 1 June, 2002;
originally announced June 2002.
-
A Simplified Model of Intrabeam Scattering
Authors:
Karl L. F. Bane
Abstract:
Beginning with the general Bjorken-Mtingwa solution, we derive a simplified model of intrabeam scattering (IBS), one valid for high energy beams in normal storage rings; our result is similar, though more accurate than a model due to Raubenheimer. In addition, we show that a modified version of Piwinski's IBS formulation (where eta squared over beta has been replaced by the dispersion invariant)…
▽ More
Beginning with the general Bjorken-Mtingwa solution, we derive a simplified model of intrabeam scattering (IBS), one valid for high energy beams in normal storage rings; our result is similar, though more accurate than a model due to Raubenheimer. In addition, we show that a modified version of Piwinski's IBS formulation (where eta squared over beta has been replaced by the dispersion invariant) at high energies asymptotically approaches the same result.
△ Less
Submitted 1 June, 2002;
originally announced June 2002.
-
An Accurate, Simplified Model of Intrabeam Scattering
Authors:
Karl L. F. Bane
Abstract:
Beginning with the general Bjorken-Mtingwa solution for intrabeam scattering (IBS) we derive an accurate, greatly simplified model of IBS, valid for high energy beams in normal storage ring lattices. In addition, we show that, under the same conditions, a modified version of Piwinski's IBS formulation (where dispersion squared over beta has been replaced by the dispersion invariant) asymptotical…
▽ More
Beginning with the general Bjorken-Mtingwa solution for intrabeam scattering (IBS) we derive an accurate, greatly simplified model of IBS, valid for high energy beams in normal storage ring lattices. In addition, we show that, under the same conditions, a modified version of Piwinski's IBS formulation (where dispersion squared over beta has been replaced by the dispersion invariant) asymptotically approaches the result of Bjorken-Mtingwa.
△ Less
Submitted 21 May, 2002;
originally announced May 2002.
-
Intrabeam Scattering Analysis of ATF Beam Measurements
Authors:
K. L. F. Bane,
H. Hayano,
K. Kubo,
T. Naito,
T. Okugi,
J. Urakawa
Abstract:
At the Accelerator Test Facility (ATF) at KEK intrabeam scattering (IBS) is a strong effect for an electron machine. It is an effect that couples all dimensions of the beam, and in April 2000, over a short period of time, all dimensions were measured as functions of current. In this report we derive a simple relation for the growth rates of emittances due to IBS. We apply the theories of Bjorken…
▽ More
At the Accelerator Test Facility (ATF) at KEK intrabeam scattering (IBS) is a strong effect for an electron machine. It is an effect that couples all dimensions of the beam, and in April 2000, over a short period of time, all dimensions were measured as functions of current. In this report we derive a simple relation for the growth rates of emittances due to IBS. We apply the theories of Bjorken-Mtingwa, Piwinski, and a formula due to Raubenheimer to the ATF parameters, and find that the results all agree (if in Piwinski's formalism we replace the dispersion squared over beta by the dispersion invariant). Finally, we compare theory, including the effect of potential well bunch lengthening, with the April 2000 measurements, and find reasonably good agreement in the energy spread and horizontal emittance dependence on current. The vertical emittance measurement, however, implies that either: there is error in the measurement (equivalent to an introduction of 0.6% x-y coupling error), or the effect of intrabeam scattering is stronger than predicted (35% stronger in growth rates).
△ Less
Submitted 2 August, 2001; v1 submitted 20 June, 2001;
originally announced June 2001.
-
Impedance Analysis of Bunch Length Measurements at the ATF Damping Ring
Authors:
K. L. F. Bane,
T. Naito,
T. Okugi,
Q. Qin,
J. Urakawa
Abstract:
We present energy spread and bunch length measurements at the Accelerator Test Facility (ATF) at KEK, as functions of current, for different ring rf voltages, and with the beam both on and off the coupling resonance. We fit the on-coupling bunch shapes to those of an impedance model consisting of a resistor and an inductor connected in series. We find that the fits are reasonably good, but that…
▽ More
We present energy spread and bunch length measurements at the Accelerator Test Facility (ATF) at KEK, as functions of current, for different ring rf voltages, and with the beam both on and off the coupling resonance. We fit the on-coupling bunch shapes to those of an impedance model consisting of a resistor and an inductor connected in series. We find that the fits are reasonably good, but that the resulting impedance is unexpectedly large.
△ Less
Submitted 29 May, 2001;
originally announced May 2001.
-
On Resonant Multi-Bunch Wakefield Effects in Linear Accelerators with Dipole Mode Detuning
Authors:
Karl L. F. Bane,
Zenghai Li
Abstract:
In this report we explore resonant multi-bunch, transverse wakefield effects in a linear accelerator in which the dipole modes of the accelerator structures have been detuned.
In this report we explore resonant multi-bunch, transverse wakefield effects in a linear accelerator in which the dipole modes of the accelerator structures have been detuned.
△ Less
Submitted 27 January, 2001;
originally announced January 2001.
-
Obtaining the Wakefield Due to Cell-to-Cell Misalignments in a Linear Accelerator Structure
Authors:
Karl L. F. Bane,
Zenghai Li
Abstract:
A linear accelerator structure, such as will be used in the linacs of the JLC/NLC collider, is composed of on the order of 100 cells. The cells are constructed as individual cups that are brazed together to form a structure. Fabrication error will result in slight cell-to-cell misalignments along the finished structure. In this report we derive an approximation to the transverse wakefield of a s…
▽ More
A linear accelerator structure, such as will be used in the linacs of the JLC/NLC collider, is composed of on the order of 100 cells. The cells are constructed as individual cups that are brazed together to form a structure. Fabrication error will result in slight cell-to-cell misalignments along the finished structure. In this report we derive an approximation to the transverse wakefield of a structure with cell-to-cell misalignments in terms of the eigenfunctions and eigenvalues of the error-free structure.
△ Less
Submitted 27 January, 2001;
originally announced January 2001.
-
Analytic Formula for Weak Multi-Bunch Beam Break-Up in a Linac
Authors:
Karl L. F. Bane,
Zenghai Li
Abstract:
In designing linear accelerator structures for multi-bunch applications we are often interested in estimating the effect of relatively weak multi-bunch beam break-up (BBU), due to the somewhat complicated wakefields of detuned structures. This, for example, is the case for the injector linacs of the JLC/NLC linear collider project. Deriving an analytical formula for such a problem is the subject…
▽ More
In designing linear accelerator structures for multi-bunch applications we are often interested in estimating the effect of relatively weak multi-bunch beam break-up (BBU), due to the somewhat complicated wakefields of detuned structures. This, for example, is the case for the injector linacs of the JLC/NLC linear collider project. Deriving an analytical formula for such a problem is the subject of this report.
△ Less
Submitted 27 January, 2001;
originally announced January 2001.
-
Intrabeam Scattering Analysis of ATF Beam Data Taken in April 2000
Authors:
K. Bane,
H. Hayano,
K. Kubo,
T. Naito,
T. Okugi,
J. Urakawa
Abstract:
In April 2000 the single bunch energy spread, bunch length, horizontal emittance, and vertical emittance were measured as functions of current in KEK's ATF damping ring. In this report the measurement results are analyzed in light of intrabeam scattering theory. The measurements are found to be relatively consistent with theory, although the measured effects appear to be stronger than theory. In…
▽ More
In April 2000 the single bunch energy spread, bunch length, horizontal emittance, and vertical emittance were measured as functions of current in KEK's ATF damping ring. In this report the measurement results are analyzed in light of intrabeam scattering theory. The measurements are found to be relatively consistent with theory, although the measured effects appear to be stronger than theory. In addition, the factor of 3 growth in vertical emittance at a current of 3 mA does not seem to be supported.
△ Less
Submitted 21 December, 2000;
originally announced December 2000.
-
Dipole Mode Detuning in the Injector Linacs of the NLC
Authors:
Karl L. F. Bane,
Zenghai Li
Abstract:
The injector linacs of the JLC/NLC project include the prelinac, the e+ drive linac, the $e- booster, and the $e+ booster. The first three will be S-band machines, the last one, an L-band machine. We have demonstrated that by using detuning alone in the accelerator structure design of these linacs we will have acceptable tolerances for emittance growth due to both injection jitter and structure…
▽ More
The injector linacs of the JLC/NLC project include the prelinac, the e+ drive linac, the $e- booster, and the $e+ booster. The first three will be S-band machines, the last one, an L-band machine. We have demonstrated that by using detuning alone in the accelerator structure design of these linacs we will have acceptable tolerances for emittance growth due to both injection jitter and structure misalignments, for both the nominal (2.8ns) and alternate (1.4ns) bunch spacings.
△ Less
Submitted 21 December, 2000; v1 submitted 6 December, 2000;
originally announced December 2000.
-
Bunch Length Measurements at the ATF Damping Ring in April 2000
Authors:
K. L. F. Bane,
T. Naito,
T. Okugi,
J. Urakawa
Abstract:
This report presents bunch length and energy spread measurements performed in April 2000 at the ATF Damping Ring, at KEK. Measurements were performed with the beam on and then off the linear (difference) coupling resonance. Due to strong intra-beam scattering in the ATF ring, the results depended strongly on the coupling.
This report presents bunch length and energy spread measurements performed in April 2000 at the ATF Damping Ring, at KEK. Measurements were performed with the beam on and then off the linear (difference) coupling resonance. Due to strong intra-beam scattering in the ATF ring, the results depended strongly on the coupling.
△ Less
Submitted 16 October, 2000;
originally announced October 2000.
-
Higher Dipole Bands in the NLC Accelerating Structure
Authors:
C. Adolphsen,
K. L. F. Bane,
V. A. Dolgashev,
K. Ko,
Z. Li,
R. Miller
Abstract:
We show that scattering matrix calculations for dipole modes between 23-43 GHz for the 206 cell detuned structure (DS) are consistent with finite element calculations and results of the uncoupled model. In particular, the rms sum wake for these bands is comparable to that of the first dipole band.
We also show that for RDDS1 uncoupled wakefield calculations for higher bands are consistent with…
▽ More
We show that scattering matrix calculations for dipole modes between 23-43 GHz for the 206 cell detuned structure (DS) are consistent with finite element calculations and results of the uncoupled model. In particular, the rms sum wake for these bands is comparable to that of the first dipole band.
We also show that for RDDS1 uncoupled wakefield calculations for higher bands are consistent with measurements. In particular, a clear 26 GHz signal in the short range wake is found in both results.
△ Less
Submitted 29 August, 2000;
originally announced August 2000.
-
Impedance of a Beam Tube with Small Corrugations
Authors:
K. L. F. Bane,
V. V. Stupakov
Abstract:
In accelerator projects involving the use of very short bunches, such as the Linac Coherent Light Source (LCLS)-where the rms bunch length in the undulator section is 30 micron-, it appears that even submicron imperfections in the beam tube surface can generate an impedance that is unacceptably large. We consider two periodic models of an imperfect, rough surface, one with small rectangular corr…
▽ More
In accelerator projects involving the use of very short bunches, such as the Linac Coherent Light Source (LCLS)-where the rms bunch length in the undulator section is 30 micron-, it appears that even submicron imperfections in the beam tube surface can generate an impedance that is unacceptably large. We consider two periodic models of an imperfect, rough surface, one with small rectangular corrugations, the other with smooth sinusoidal oscillations. We compare the impedance of these two models.
△ Less
Submitted 28 August, 2000; v1 submitted 20 August, 2000;
originally announced August 2000.
-
Dipole Mode Detuning in the NLC Injector Linacs
Authors:
K. L. F. Bane,
Z. Li
Abstract:
The injector linacs of the JLC/NLC comprise the e+ booster, the e- drive linac, the e+ booster, and the two prelinacs. These four systems together transport the two types of beams from the 80 MeV point at the end of their respective bunchers up to the storage rings, and then from the storage rings to the 10 GeV point at the beginning of the bunch compressors. Nominally, the e+ booster structure…
▽ More
The injector linacs of the JLC/NLC comprise the e+ booster, the e- drive linac, the e+ booster, and the two prelinacs. These four systems together transport the two types of beams from the 80 MeV point at the end of their respective bunchers up to the storage rings, and then from the storage rings to the 10 GeV point at the beginning of the bunch compressors. Nominally, the e+ booster structure will be L-band and the others S-band. In transport through these linacs it is important that the emittances and particle losses stay within specified tolerances. In particular, the effects of the dipole wakefield-especially the long-range dipole wakefield-need to be carefully considered. We present designs of the injector linac structures that employ simple mode detuning, without damping, and that allow us to satisfy our tolerance requirements, for both the nominal (2.8 ns) and alternate (1.4 ns) bunch spacing options.
△ Less
Submitted 18 August, 2000;
originally announced August 2000.
