-
The influence of nitrogen ion implantation on the microstructure and chemical composition of a thin layer on the biodegradable Zn-0.8Mg-0.2Sr substrate
Authors:
Jan Pinc,
Petr Vlcak,
Miroslav Lebeda,
Vilem Bartunek,
Vojtech Smola,
Marek Vronka,
Jan Drahokoupil,
Zdenek Weiss,
Petr Svora,
Hana Lesakova,
Katerina Sindelarova,
Orsolya Molnarova,
Tomas Horazdovsky,
Tomas Studecky,
Pavel Salvetr,
Jiri Kubasek,
Jaroslav Capek,
Andrea Skolakova
Abstract:
In this research, the influence of the N+ ion implantation process on the microstructure of a biodegradable Zn-0.8Mg-0.2Sr alloy was investigated using various experimental techniques. Microscopic analysis revealed that a fluence of 17x10^17 ions/cm^2 resulted in the oversaturation of pure Zn and Mg2Zn11 surfaces, leading to the formation of nano/micro-porous layers up to 400 nm thick. The behavio…
▽ More
In this research, the influence of the N+ ion implantation process on the microstructure of a biodegradable Zn-0.8Mg-0.2Sr alloy was investigated using various experimental techniques. Microscopic analysis revealed that a fluence of 17x10^17 ions/cm^2 resulted in the oversaturation of pure Zn and Mg2Zn11 surfaces, leading to the formation of nano/micro-porous layers up to 400 nm thick. The behavior of the Zn-0.8Mg-0.2Sr alloy was observed to be similar to that of the individual pure phases, albeit without the creation of pore structures. A limited formation of MgO and Mg3N2 was observed on the alloy surface, although the overall presence of Mg significantly increased from 0.8 to 15 wt.%. This increase was caused by the decomposition of the Mg2Zn11 phase during the process and subsequent diffusion of Mg toward the surface. The absence of Zn3N2 within the samples could be explained by the thermodynamic instability and low Zn-N affinity. Despite the absence of zinc nitride, GD-OES confirmed 10 at. % of nitrogen in the pure zinc, suggesting a possible accommodation of N atoms in the interstitial positions. This study points out to the complex nature of the process and highlights other promising directions for future research.
△ Less
Submitted 9 July, 2024;
originally announced July 2024.
-
Advantages of rapid solidification over casting of Mg-0.4Zn-1Y alloy
Authors:
Drahomir Dvorsky,
Shin-Ichi Inoue,
Ayami Yoshida,
Jiri Kubasek,
Jan Duchon,
Esther de Prado,
Andrea Skolakova,
Klara Hosova,
Petr Svora,
Yoshihito Kawamura
Abstract:
The Mg-Y-Zn magnesium alloy system is commonly recognized for its remarkable combination of high strength and ductility, achieved even with minimal amounts of alloying elements. This exceptional performance is attributed to its unique microstructure, which includes Long-Period Stacking Ordered (LPSO) phases or the distinctive microstructure derived from the LPSO phase, referred to as the Mille-Feu…
▽ More
The Mg-Y-Zn magnesium alloy system is commonly recognized for its remarkable combination of high strength and ductility, achieved even with minimal amounts of alloying elements. This exceptional performance is attributed to its unique microstructure, which includes Long-Period Stacking Ordered (LPSO) phases or the distinctive microstructure derived from the LPSO phase, referred to as the Mille-Feuille structure (MFS). This study systematically compares the traditional ingot metallurgy method with the rapid solidification technique, coupled with diverse heat treatments and extrusion processes. Microscopic analyses reveal variations in the presence of LPSO phases, Mille-Feuille structure, and grain size, leading to divergent mechanical and corrosion properties. The rapid solidification approach stands out, ensuring superior mechanical properties alongside a reasonable corrosion rate.
△ Less
Submitted 9 July, 2024;
originally announced July 2024.
-
Harmonizing Microstructures and Enhancing Mechanical Resilience: Novel Powder Metallurgy Approach for Zn-Mg Alloys
Authors:
Anna Boukalova,
Jiri Kubasek,
David Necas,
Peter Minarik,
Crtomir Donik,
Drahomir Dvorsky,
Dalibor Vojtech,
Alena Michalcova,
Matjaz Godec,
Irena Paulin
Abstract:
Zinc alloys are recognised for their excellent biocompatibility and favourable corrosion rates, making them suitable for bioabsorbable implants. However, their mechanical properties necessitate improvement to fulfil the rigorous requirements of biomedical applications. This research focuses on engineering pseudo-harmonic structures within zinc alloys through a comprehensive method combining mechan…
▽ More
Zinc alloys are recognised for their excellent biocompatibility and favourable corrosion rates, making them suitable for bioabsorbable implants. However, their mechanical properties necessitate improvement to fulfil the rigorous requirements of biomedical applications. This research focuses on engineering pseudo-harmonic structures within zinc alloys through a comprehensive method combining mechanical alloying, spark plasma sintering, and hot extrusion techniques. This fabrication process results in a composite material characterised by a soft core surrounded by a continuous, three-dimensional, ultrafine-grained hard shell. The experiment involved blending pure zinc with Zn-1Mg alloy powder, leading to the formation of both ductile zinc and fine-grained Zn-1Mg regions. While the Mg2Zn11 intermetallic phase was found to enhance the alloy's mechanical strength, the presence of oxide shells adversely affected the material's properties. The elimination of these shells via hot extrusion markedly improved the alloy's tensile strength, reaching an average value of tensile strength of 333 MPa. This study provides significant insights into the material engineering of zinc-based alloys for biodegradable implant applications, demonstrating a viable approach to optimising their mechanical performance.
△ Less
Submitted 1 July, 2024;
originally announced July 2024.
-
Adjustable coupling and in-situ variable frequency EPR probe with loop-gap resonators for spectroscopy up to X-band
Authors:
G. Joshi,
J. Kubasek,
I. Nikolov,
B. Sheehan,
T. A. costa,
R. A. A. Cassaro,
J. R. Friedman
Abstract:
In standard electron paramagnetic resonance (EPR) spectroscopy, the frequency of an experiment is set and the spectrum is acquired using magnetic field as the independent variable. There are cases in which it is desirable instead to fix the field and tune the frequency such as when studying avoided level crossings. We have designed and tested an adjustable frequency and variable coupling EPR probe…
▽ More
In standard electron paramagnetic resonance (EPR) spectroscopy, the frequency of an experiment is set and the spectrum is acquired using magnetic field as the independent variable. There are cases in which it is desirable instead to fix the field and tune the frequency such as when studying avoided level crossings. We have designed and tested an adjustable frequency and variable coupling EPR probe with loop-gap resonators (LGRs) that works at a temperature down to 1.8 K. The frequency is tuned by adjusting the height of a dielectric piece of sapphire inserted into the gap of an LGR; coupling of the microwave antenna is varied with the height of antenna above the LGR. Both coupling antenna and dielectric are located within the cryogenic sample chamber, but their motion is controlled with external micrometers located outside the cryostat. The frequency of the LGR can be adjusted by more than 1 GHz. To cover a wide range of frequencies, different LGRs can be designed to cover frequencies up to X-band. We demonstrate the operation of our probe by mapping out avoided crossings for the Ni$_4$ single-molecule magnet to determine the tunnel splittings with high precision.
△ Less
Submitted 23 October, 2019;
originally announced October 2019.
-
Instrument for in-situ orientation of superconducting thin-film resonators used for electron-spin resonance experiments
Authors:
Andrew Mowry,
Yiming Chen,
James Kubasek,
Jonathan R. Friedman
Abstract:
When used in Electron-Spin Resonance (ESR) measurements, superconducting thin-film resonators must be precisely oriented relative to the external magnetic field in order to prevent the trapping of magnetic flux and the associated degradation of resonator performance. We present a compact design solution for this problem that allows in-situ control of the orientation of the resonator at cryogenic t…
▽ More
When used in Electron-Spin Resonance (ESR) measurements, superconducting thin-film resonators must be precisely oriented relative to the external magnetic field in order to prevent the trapping of magnetic flux and the associated degradation of resonator performance. We present a compact design solution for this problem that allows in-situ control of the orientation of the resonator at cryogenic temperatures. Tests of the apparatus show that when proper alignment is achieved, there is almost no hysteresis in the field dependence of the resonant frequency.
△ Less
Submitted 16 January, 2015; v1 submitted 3 January, 2015;
originally announced January 2015.
