Showing 1–50 of 64 results for author: Mokhov, N V

Critical problems of energy frontier Muon Colliders: optics, magnets and radiation

Authors: Yu. I. Alexahin, E. Barzi, E. Gianfelice-Wendt, V. Kapin, V. V. Kashikhin, N. V. Mokhov, I. Novitski, V. Shiltsev, S. Striganov, I. Tropin, A. V. Zlobin

Abstract: This White Paper brings together our previous studies on a Muon Collider (MC) and presents a design concept of the 6 TeV MC optics, the superconducting (SC) magnets, and a preliminary analysis of the protection system to reduce magnet radiation loads as well as particle backgrounds in the detector. The SC magnets and detector protection considerations impose strict limitations on the lattice choic… ▽ More This White Paper brings together our previous studies on a Muon Collider (MC) and presents a design concept of the 6 TeV MC optics, the superconducting (SC) magnets, and a preliminary analysis of the protection system to reduce magnet radiation loads as well as particle backgrounds in the detector. The SC magnets and detector protection considerations impose strict limitations on the lattice choice, hence the design of the collider optics, magnets and Machine Detector Interface (MDI) are closely intertwined. As a first approximation we use the Interaction Region (IR) design with beta-star=3 mm, whereas for the arcs we re-scale the arc cell design of the 3 TeV MC. Traditional cos-theta coil geometry and Nb3Sn superconductor were used to provide field maps for the analysis and optimization of the arc lattice and IR design, as well as for studies of beam dynamics and magnet protection against radiation. The stress management in the coil will be needed to avoid large degradation or even damage of the brittle SC coils. In the assumed IR designs, the dipoles close to the Interaction Point (IP) and tungsten masks in each IR (to protect magnets) help reducing background particle fluxes in the detector by a substantial factor. The tungsten nozzles in the 6 to 600 cm region from the IP, assisted by the detector solenoid field, trap most of the decay electrons created close to the IP as well as most of the incoherent electron-positron pairs generated in the IP. With sophisticated tungsten, iron, concrete and borated polyethylene shielding in the MDI region, the total reduction of background loads by more than three orders of magnitude can be achieved. △ Less

Submitted 19 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021. arXiv admin note: text overlap with arXiv:1204.6721

Solving Critical Problems of the Muon Collider Higgs Factory: Optics, Magnets and their Protection, Detector Backgrounds

Authors: Yu. Alexahin, E. Gianfelice-Wendt, V. Kapin, V. V. Kashikhin, N. V. Mokhov, S. I. Striganov, I. S. Tropin, A. V. Zlobin

Abstract: A low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). Magnet designs are proposed which provide high operating gr… ▽ More A low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). Magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams (due to low beta*), as well as a cooling system to intercept the large heat deposition from the showers induced by decay electrons. The distribution of heat deposition in the MC SR lattice elements requires large-aperture magnets in order to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intensive simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in the magnet aperture optimized individually for each magnet. These also reduce the background particle fluxes in the collider detector. △ Less

Submitted 16 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021. arXiv admin note: substantial text overlap with arXiv:1806.08883, arXiv:1501.07624

Detector Backgrounds at the Higgs Factory Muon Collider: MARS vs FLUKA

Authors: N. V. Mokhov, S. I. Striganov, I. S. Tropin, T. W. Markiewicz, T. Maruyama

Abstract: Simulations for the 125-GeV Higgs Factory (HF) Muon Collider (MC) have shown large background particle loads on the collider detector. To verify level, source and composition of background calculations were performed using FLUKA and MARS codes for two shielding configurations. After comprehensive tuning of muon beam parameters, geometry setups and scoring procedures, background particle distributi… ▽ More Simulations for the 125-GeV Higgs Factory (HF) Muon Collider (MC) have shown large background particle loads on the collider detector. To verify level, source and composition of background calculations were performed using FLUKA and MARS codes for two shielding configurations. After comprehensive tuning of muon beam parameters, geometry setups and scoring procedures, background particle distributions at the detector entrance were simulated and compared. The spatial distributions and energy spectra of background particles obtained by two codes are rather similar. Average numbers of background particles simulated using MARS and FLUKA agree within a factor of two. △ Less

Submitted 7 August, 2018; v1 submitted 6 August, 2018; originally announced August 2018.

Comments: 5 pages, 3 figures

A Study of Muon Collider Background Rejection Criteria in Silicon Vertex and Tracker Detectors

Authors: V. Di Benedetto, C. Gatto, A. Mazzacane, N. V. Mokhov, S. I. Striganov, N. K. Terentiev

Abstract: The hit response of silicon vertex and tracking detectors to muon collider beam background and results of a study of hit reducing techniques are presented. The background caused by decays of the 750 GeV/c m+ and m- beams was simulated using the MARS15 program, which included the infrastructure of the beam line elements near the detector and the 10 degree nozzles that shield the detector from this… ▽ More The hit response of silicon vertex and tracking detectors to muon collider beam background and results of a study of hit reducing techniques are presented. The background caused by decays of the 750 GeV/c m+ and m- beams was simulated using the MARS15 program, which included the infrastructure of the beam line elements near the detector and the 10 degree nozzles that shield the detector from this background. The ILCRoot framework, along with the Geant4 program, was used to simulate the hit response of the silicon vertex and tracker detectors to the muon decay background remaining after the shielding nozzles. The background hit reducing techniques include timing, energy deposition, and hit location correlation in the double layer geometry. △ Less

Submitted 29 June, 2018; originally announced July 2018.

Comments: 10 pages, 20 figures

The Higgs Factory Muon Collider Superconducting Magnets and Their Protection Against Beam Decay Radiation

Authors: N. V. Mokhov, V. V. Kashikhin, S. I. Striganov, I. S. Tropin, A. V. Zlobin

Abstract: Low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). The magnet designs are proposed which provide high operating… ▽ More Low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). The magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams due to low \b{eta}* as well as the cooling system to intercept the large heat deposition from the showers induced by decay electrons. Specific distribution of heat deposition in the lattice elements MC SR requires large aperture magnets to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intense simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in magnet aperture optimized for each magnet. It also reduces the background particle fluxes in the collider detector. △ Less

Submitted 19 July, 2018; v1 submitted 22 June, 2018; originally announced June 2018.

Comments: 14 pages, 12 figures

Report number: Fermilab-PUB-18-300-APC-TD

Preliminary Modeling Of Radiation Levels At The Fermilab PIP-II Linac

Authors: L. Lari, F. Cerutti, L. S. Esposito, C. Baffes, S. J. Dixon, N. V. Mokhov, I. Rakhno, I. S. Tropin

Abstract: PIP-II is the Fermilab's flagship project for providing powerful, high-intensity proton beams to the laboratory's experiments. The heart of PIP-II is an 800-MeV superconducting linac accelerator. It will be located in a new tunnel with new service buildings and connected to the present Booster through a new transfer line. To support the design of civil engineering and mechanical integration, this… ▽ More PIP-II is the Fermilab's flagship project for providing powerful, high-intensity proton beams to the laboratory's experiments. The heart of PIP-II is an 800-MeV superconducting linac accelerator. It will be located in a new tunnel with new service buildings and connected to the present Booster through a new transfer line. To support the design of civil engineering and mechanical integration, this paper provides preliminary estimation of radiation level in the gallery at an operational beam loss limit of 0.1 W/m, by means of Monte Carlo calculations with FLUKA and MARS15 codes. △ Less

Submitted 14 June, 2018; originally announced June 2018.

Comments: 4 pp. Proceedings of IPAC2018, Vancouver, BC, Canada

Report number: Fermilab-Conf-18-119-AD

Activation assessment of the soil around the ESS accelerator tunnel

Authors: I. L. Rakhno, N. V. Mokhov, I. S. Tropin, D. Ene

Abstract: Activation of the soil surrounding the ESS accelerator tunnel calculated by the MARS15 code is presented. A detailed composition of the soil, that comprises about 30 different chemical elements, is considered. Spatial distributions of the produced activity are provided in both transverse and longitudinal direction. A realistic irradiation profile for the entire planned lifetime of the facility is… ▽ More Activation of the soil surrounding the ESS accelerator tunnel calculated by the MARS15 code is presented. A detailed composition of the soil, that comprises about 30 different chemical elements, is considered. Spatial distributions of the produced activity are provided in both transverse and longitudinal direction. A realistic irradiation profile for the entire planned lifetime of the facility is used. The nuclear transmutation and decay of the produced radionuclides is calculated with the DeTra code which is a built-in tool for the MARS15 code. Radionuclide production by low-energy neutrons is calculated using the ENDF/B-VII evaluated nuclear data library. In order to estimate quality of this activation assessment, a comparison between calculated and measured activation of various foils in a similar radiation environment is presented. △ Less

Submitted 11 January, 2018; originally announced January 2018.

Comments: 20 pp. Presented at the 4th International Workshop on Accelerator Radiation Induced Activation (ARIA'17) held at the European Spallation Source (ESS) on May 22-24, 2017 in Lund, Sweden

Report number: Fermilab-Conf-17-378-APC

Measurements and calculations of air activation in the NuMI neutrino production facility at Fermilab with the 120-GeV proton beam on target

Authors: I. L. Rakhno, J. Hylen, P. Kasper, N. V. Mokhov, M. Quinn, S. I. Striganov, K. Vaziri

Abstract: Measurements and calculations of the air activation at a high-energy proton accelerator are described. The quantity of radionuclides released outdoors depends on operation scenarios including details of the air exchange inside the facility. To improve the prediction of the air activation levels, the MARS15 Monte Carlo code radionuclide production model was modified to be used for these studies. Me… ▽ More Measurements and calculations of the air activation at a high-energy proton accelerator are described. The quantity of radionuclides released outdoors depends on operation scenarios including details of the air exchange inside the facility. To improve the prediction of the air activation levels, the MARS15 Monte Carlo code radionuclide production model was modified to be used for these studies. Measurements were done to benchmark the new model and verify its use in optimization studies for the new DUNE experiment at the Long Baseline Neutrino Facility (LBNF) at Fermilab. The measured production rates for the most important radionuclides - $^{11}$C, $^{13}$N, $^{15}$O and $^{41}$Ar - are in a good agreement with those calculated with the improved MARS15 code. △ Less

Submitted 30 November, 2017; originally announced December 2017.

Comments: 14 pp

Report number: Fermilab-Pub-17-382-AD-APC-ESH

Energy Deposition and Radiation to Electronics

Authors: A. Bignami, F. Broggi, M. Brugger, F. Cerutti, L. S. Esposito, A. Lechner, N. V. Mokhov, I. L. Rakhno, C. Santini, E. Skordis, I. S. Tropin

Abstract: Chapter 10 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme tempe… ▽ More Chapter 10 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC. △ Less

Submitted 26 May, 2017; originally announced May 2017.

Comments: 16 pages, chapter 10 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. arXiv admin note: text overlap with arXiv:1504.00594

Journal ref: CERN Yellow Report CERN 2015-005, pp.171-186

Dark Current and Radiation Shielding Studies For The ILC Main Linac

Authors: Nikolai V. Mokhov, Igor L. Rakhno, Nikolay A. Solyak, Alexander Sukhanov, Igor S. Tropin

Abstract: Electrons of dark current (DC), generated in high-gradient superconducting RF cavities (SRF) due to field emission, can be accelerated up to very high energies-19 GeV in the case of the International Linear Collider (ILC) main linac-before they are removed by focusing and steering magnets. Electromagnetic and hadron showers generated by such electrons can represent a significant radiation threat t… ▽ More Electrons of dark current (DC), generated in high-gradient superconducting RF cavities (SRF) due to field emission, can be accelerated up to very high energies-19 GeV in the case of the International Linear Collider (ILC) main linac-before they are removed by focusing and steering magnets. Electromagnetic and hadron showers generated by such electrons can represent a significant radiation threat to the linac equipment and personnel. In our study, an operational scenario is analysed which is believed can be considered as the worst case scenario for the main linac regarding the DC contribution to the radiation environment in the main linac tunnel. A detailed modeling is performed for the DC electrons which are emitted from the surface of the SRF cavities and can be repeatedly accelerated in the high-gradient fields in many SRF cavities. Results of MARS15 Monte Carlo calculations, performed for the current main linac tunnel design, reveal that the prompt dose design level of 25 μみゅーSv/hr in the service tunnel can be provided by a 2.3-m thick concrete wall between the main and service tunnels. △ Less

Submitted 5 May, 2017; originally announced May 2017.

Comments: 12 pp. Presented paper at the 13th Meeting of the task-force on Shielding aspects of Accelerators, Targets and Irradiation Facilities (SATIF-13), HZDR, October 10-12, 2016, Dresden, Germany

Report number: Fermilab-Conf-16-542-APC-TD

Update On The Code Intercomparison and Benchmark For Muon Fluence and Absorbed Dose Induced By An 18-GeV Electron Beam After Massive Iron Shielding

Authors: A. Fassò, A. Ferrari, A. Ferrari, N. V. Mokhov, S. E. Mueller, W. R. Nelson, S. Roesler, T. Sanami, S. I. Striganov, R. Versaci

Abstract: In 1974, Nelson, Kase and Svensson published an experimental investigation on muon shielding around SLAC high-energy electron accelerators. They measured muon fluence and absorbed dose induced by 14 and 18 GeV electron beams hitting a copper/water beamdump and attenuated in a thick steel shielding. In their paper, they compared the results with the theoretical models available at that time. In o… ▽ More In 1974, Nelson, Kase and Svensson published an experimental investigation on muon shielding around SLAC high-energy electron accelerators. They measured muon fluence and absorbed dose induced by 14 and 18 GeV electron beams hitting a copper/water beamdump and attenuated in a thick steel shielding. In their paper, they compared the results with the theoretical models available at that time. In order to compare their experimental results with present model calculations, we use the modern transport Monte Carlo codes MARS15, FLUKA2011 and GEANT4 to model the experimental setup and run simulations. The results are then compared between the codes, and with the SLAC data. △ Less

Submitted 5 May, 2017; originally announced May 2017.

Comments: 14 pp. Presented paper at the 13th Meeting of the task-force on Shielding aspects of Accelerators, Targets and Irradiation Facilities (SATIF-13), HZDR, October 10-12, 2016, Dresden, Germany. arXiv admin note: substantial text overlap with arXiv:1502.01681

Report number: Fermilab-Conf-16-574-APC

MARS15 Simulation Of Radiation Environment At The ESS Linac

Authors: N. V. Mokhov, Yu. I. Eidelman, I. L. Rakhno, L. Tchelidze, I. S. Tropin

Abstract: Comprehensive studies with the MARS15(2016) Monte-Carlo code are described on evaluation of prompt and residual radiation levels induced by nominal and accidental beam losses in the 5-MW, 2-GeV European Spallation Source (ESS) Linac. These are to provide a basis for radiation shielding design verification through the accelerator complex. The calculation model is based on the latest engineering des… ▽ More Comprehensive studies with the MARS15(2016) Monte-Carlo code are described on evaluation of prompt and residual radiation levels induced by nominal and accidental beam losses in the 5-MW, 2-GeV European Spallation Source (ESS) Linac. These are to provide a basis for radiation shielding design verification through the accelerator complex. The calculation model is based on the latest engineering design and includes a sophisticated algorithm for particle tracking in the machine RF cavities as well as a well-established model of the beam loss. Substantial efforts were put in solving the deep-penetration problem for the thick shielding around the tunnel with numerous complex penetrations. It allowed us to study in detail not only the prompt dose, but also component and air activation, radiation loads on the soil outside the tunnel, and skyshine studies for the complicated 3-D surface above the machine. Among the other things, the newest features in MARS15 (2016), such as a ROOT-based beamline builder and a TENDL-based event generator for nuclear interactions below 100 MeV, were very useful in this challenging application. △ Less

Submitted 4 May, 2017; originally announced May 2017.

Comments: 15 pp. Presented paper at the 13th Meeting of the task-force on Shielding aspects of Accelerators, Targets and Irradiation Facilities (SATIF-13), HZDR, October 10-12, 2016, Dresden, Germany

Report number: Fermilab-Conf-16-543-APC

Design Of The LBNF Beamline

Authors: V. Papadimitriou, K. Ammigan, J. Anderson Jr., K. E. Anderson, R. Andrews, V. Bocean, C. F. Crowley, N. Eddy, B. D. Hartsell, S. Hays, P. Hurh, J. Hylen, J. A. Johnstone, P. Kasper, T. Kobilarcik, G. E. Krafczyk, B. Lundberg, A. Marchionni, N. V. Mokhov, C. D. Moore, D. Pushka, I. Rakhno, S. D. Reitzner, P. Schlabach, V. Sidorov , et al. (9 additional authors not shown)

Abstract: The Long Baseline Neutrino Facility (LBNF) will utilize a beamline located at Fermilab to provide and aim a neutrino beam of sufficient intensity and appropriate energy range toward the Deep Underground Neutrino Experiment (DUNE) detectors, placed deep underground at the SURF Facility in Lead, South Dakota. The primary proton beam (60-120 GeV) will be extracted from the MI-10 section of Fermilab's… ▽ More The Long Baseline Neutrino Facility (LBNF) will utilize a beamline located at Fermilab to provide and aim a neutrino beam of sufficient intensity and appropriate energy range toward the Deep Underground Neutrino Experiment (DUNE) detectors, placed deep underground at the SURF Facility in Lead, South Dakota. The primary proton beam (60-120 GeV) will be extracted from the MI-10 section of Fermilab's Main Injector. Neutrinos will be produced when the protons interact with a solid target to produce mesons which will be subsequently focused by magnetic horns into a 194m long decay pipe where they decay into muons and neutrinos. The parameters of the facility were determined taking into account the physics goals, spatial and radiological constraints, and the experience gained by operating the NuMI facility at Fermilab. The Beamline facility is designed for initial operation at a proton-beam power of 1.2 MW, with the capability to support an upgrade to 2.4 MW. LBNF/DUNE obtained CD-1 approval in November 2015. We discuss here the design status and the associated challenges as well as the R&D and plans for improvements before baselining the facility. △ Less

Submitted 14 April, 2017; originally announced April 2017.

Comments: 3 pp

Report number: Fermilab-Conf-16-163-AD

Design of the LBNF Beamline Target Station

Authors: S. Tariq, K. Ammigan, K. Anderson, S. A. Buccellato, C. F. Crowley, B. D. Hartsell, P. Hurh, J. Hylen, P. Kasper, G. E. Krafczyk, A. Lee, B. Lundberg, A. Marchionni, N. V. Mokhov, C. D. Moore, V. Papadimitriou, D. Pushka, I. Rakhno, S. D. Reitzner, V. Sidorov, A. M. Stefanik, I. S . Tropin, K. Vaziri, K. Williams, R. M. Zwaska , et al. (1 additional authors not shown)

Abstract: The Long Baseline Neutrino Facility (LBNF) project will build a beamline located at Fermilab to create and aim an intense neutrino beam of appropriate energy range toward the DUNE detectors at the SURF facility in Lead, South Dakota. Neutrino production starts in the Target Station, which consists of a solid target, magnetic focusing horns, and the associated sub-systems and shielding infrastructu… ▽ More The Long Baseline Neutrino Facility (LBNF) project will build a beamline located at Fermilab to create and aim an intense neutrino beam of appropriate energy range toward the DUNE detectors at the SURF facility in Lead, South Dakota. Neutrino production starts in the Target Station, which consists of a solid target, magnetic focusing horns, and the associated sub-systems and shielding infrastructure. Protons hit the target producing mesons which are then focused by the horns into a helium-filled decay pipe where they decay into muons and neutrinos. The target and horns are encased in actively cooled steel and concrete shielding in a chamber called the target chase. The reference design chase is filled with air, but nitrogen and helium are being evaluated as alternatives. A replaceable beam window separates the decay pipe from the target chase. The facility is designed for initial operation at 1.2 MW, with the ability to upgrade to 2.4 MW, and is taking advantage of the experience gained by operating Fermilab's NuMI facility. We discuss here the design status, associated challenges, and ongoing R&D and physics-driven component optimization of the Target Station. △ Less

Submitted 21 December, 2016; originally announced December 2016.

Comments: 3 pp

Report number: Fermilab-Conf-16-433-AD-APC-ESH-ND

Beam-Material Interaction

Authors: N. V. Mokhov, F. Cerutti

Abstract: Th is paper is motivated by the growing importance of better understanding of the phenomena and consequences of high- intensity energetic particle beam interactions with accelerator, generic target , and detector components. It reviews the principal physical processes of fast-particle interactions with matter, effects in materials under irradiation, materials response, related to component lifetim… ▽ More Th is paper is motivated by the growing importance of better understanding of the phenomena and consequences of high- intensity energetic particle beam interactions with accelerator, generic target , and detector components. It reviews the principal physical processes of fast-particle interactions with matter, effects in materials under irradiation, materials response, related to component lifetime and performance, simulation techniques, and methods of mitigating the impact of radiation on the components and envir onment in challenging current and future application △ Less

Submitted 8 August, 2016; originally announced August 2016.

Comments: 28 pages, contribution to the 2014 Joint International Accelerator School: Beam Loss and Accelerator Protection, Newport Beach, CA, USA , 5-14 Nov 2014

Journal ref: CERN Yellow Report CERN-2016-002, pp.83-110

Energy deposition and radiological studies for the LBNF Hadron Absorber

Authors: I. L. Rakhno, N. V. Mokhov, I. S. Tropin, Y. I. Eidelman

Abstract: Results of detailed Monte Carlo energy deposition and radiological studies performed for the LBNF hadron absorber with the MARS15 code are described. The model of the entire facility, that includes a pion-production target, focusing horns, target chase, decay channel, hadron absorber system - all with corresponding radiation shielding - was developed using the recently implemented ROOT-based geome… ▽ More Results of detailed Monte Carlo energy deposition and radiological studies performed for the LBNF hadron absorber with the MARS15 code are described. The model of the entire facility, that includes a pion-production target, focusing horns, target chase, decay channel, hadron absorber system - all with corresponding radiation shielding - was developed using the recently implemented ROOT-based geometry option in the MARS15 code. Both normal operation and accidental conditions were studied. Results of detailed thermal calculations with the ANSYS code helped to select the most viable design options. △ Less

Submitted 25 June, 2015; originally announced June 2015.

Comments: 4 pp. Presented at the 6th International Particle Accelerator Conference (IPAC 15), May 3-8, 2015, Richmond, VA, USA

Report number: FERMILAB-CONF-15-175-APC

Modeling proton- and light ion-induced reactions at low energies in the MARS15 code

Authors: I. L. Rakhno, N. V. Mokhov, K. K. Gudima

Abstract: An implementation of both ALICE code and TENDL evaluated nuclear data library in order to describe nuclear reactions induced by low-energy projectiles in the Monte Carlo code MARS15 is presented. Comparisons between results of modeling and experimental data on reaction cross sections and secondary particle distributions are shown. An implementation of both ALICE code and TENDL evaluated nuclear data library in order to describe nuclear reactions induced by low-energy projectiles in the Monte Carlo code MARS15 is presented. Comparisons between results of modeling and experimental data on reaction cross sections and secondary particle distributions are shown. △ Less

Submitted 25 June, 2015; originally announced June 2015.

Comments: 5 pp. Presented at the 6th International Particle Accelerator Conference (IPAC 15), May 3-8, 2015, Richmond, VA, USA. arXiv admin note: substantial text overlap with arXiv:1501.07597

Report number: FERMILAB-15-174-APC

Energy deposition studies for the High-Luminosity Large Hadron Collider inner triplet magnets

Authors: N. V. Mokhov, I. L. Rakhno, I. S. Tropin, F. Cerutti, L. S. Esposito, A. Lechner

Abstract: A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3… ▽ More A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3000 fb-1, the peak dose in the innermost magnet insulator ranges from 20 to 35 MGy. Dynamic heat loads to the triplet magnet cold mass are calculated to evaluate the cryogenic capability. In general, FLUKA and MARS results are in a very good agreement. △ Less

Submitted 2 April, 2015; originally announced April 2015.

Comments: 24 pp

Report number: Fermilab-PUB-15-095-APC

Current status of the LBNE neutrino beam

Authors: Craig Damon Moore, Ken Bourkland, Cory Francis Crowley, Patrick Hurh, James Hylen, Byron Lundberg, Alberto Marchionni, Mike McGee, Nikolai V. Mokhov, Vaia Papadimitriou, Rob Plunkett, Sarah Diane Reitzner, Andrew M Stefanik, Gueorgui Velev, Karlton Williams, Robert Miles Zwaska

Abstract: The Long Baseline Neutrino Experiment (LBNE) will utilize a neutrino beamline facility located at Fermilab. The facility is designed to aim a beam of neutrinos toward a detector placed in South Dakota. The neutrinos are produced in a three-step process. First, protons from the Main Injector hit a solid target and produce mesons. Then, the charged mesons are focused by a set of focusing horns into… ▽ More The Long Baseline Neutrino Experiment (LBNE) will utilize a neutrino beamline facility located at Fermilab. The facility is designed to aim a beam of neutrinos toward a detector placed in South Dakota. The neutrinos are produced in a three-step process. First, protons from the Main Injector hit a solid target and produce mesons. Then, the charged mesons are focused by a set of focusing horns into the decay pipe, towards the far detector. Finally, the mesons that enter the decay pipe decay into neutrinos. The parameters of the facility were determined by an amalgam of the physics goals, the Monte Carlo modeling of the facility, and the experience gained by operating the NuMI facility at Fermilab. The initial beam power is expected to be ~700 kW, however some of the parameters were chosen to be able to deal with a beam power of 2.3 MW. The LBNE Neutrino Beam has made significant changes to the initial design through consideration of numerous Value Engineering proposals and the current design is described. △ Less

Submitted 6 February, 2015; originally announced February 2015.

Comments: 3 pp

Report number: FERMILAB-CONF-13-121-AD

Code intercomparison and benchmark for muon fluence and absorbed dose induced by an 18-GeV electron beam after massive iron shielding

Authors: Alberto Fasso, Alfredo Ferrari, Anna Ferrari, Nikolai V. Mokhov, Stefan E. Mueller, Walter Ralph Nelson, Stefan Roesler, Toshiya Sanami, Sergei I. Striganov, Roberto Versaci

Abstract: In 1974, Nelson, Kase, and Svenson published an experimental investigation on muon shielding using the SLAC high energy LINAC. They measured muon fluence and absorbed dose induced by a 18 GeV electron beam hitting a copper/water beam dump and attenuated in a thick steel shielding. In their paper, they compared the results with the theoretical mode ls available at the time. In order to compare thei… ▽ More In 1974, Nelson, Kase, and Svenson published an experimental investigation on muon shielding using the SLAC high energy LINAC. They measured muon fluence and absorbed dose induced by a 18 GeV electron beam hitting a copper/water beam dump and attenuated in a thick steel shielding. In their paper, they compared the results with the theoretical mode ls available at the time. In order to compare their experimental results with present model calculations, we use the modern transport Monte Carlo codes MARS15, FLUKA2011 and GEANT4 to model the experimental setup and run simulations. The results will then be compared between the codes, and with the SLAC data. △ Less

Submitted 5 February, 2015; originally announced February 2015.

Comments: 10 pp. Presented paper at the 12th Workshop on Shielding Aspects of Accelerators, Targets and Irradiation Facilities, SATIF-12, Fermilab, April 28-30, 2014

Report number: FERMILAB-CONF-14-220-APC

Activation Products from Copper and Steel Samples Exposed to Showers Produced by 8 GeV Protons Lost in the Fermilab Main Injector Collimation System

Authors: Bruce C. Brown, Nikolai V. Mokhov, Vitaly S. Pronskikh

Abstract: In conjunction with efforts to predict residual radiation levels in the Fermilab Main Injector, measurements of residual radiation were correlated with the time history of losses. Detailed examination suggested that the list of radioactive isotopes used for fitting was incomplete. We will report on activation studies of magnet steel and copper samples which we irradiated adjacent to the Fermilab M… ▽ More In conjunction with efforts to predict residual radiation levels in the Fermilab Main Injector, measurements of residual radiation were correlated with the time history of losses. Detailed examination suggested that the list of radioactive isotopes used for fitting was incomplete. We will report on activation studies of magnet steel and copper samples which we irradiated adjacent to the Fermilab Main Injector collimation system. Our results identified several additional radioactive isotopes of interest. The MARS15 studies using a simplified model are compared with measurements. The long half-life isotopes will grow in importance as operation stretches to a second decade and as loss rates rise. These studies allow us to predict limits on these concerns. △ Less

Submitted 5 February, 2015; originally announced February 2015.

Comments: 9 pp

Report number: FERMILAB-CONF-14-178-AD-APC

Energy Deposition Studies for the Hi-Lumi LHC Inner Triplet Magnets

Authors: N. V. Mokhov, I. L. Rakhno, S. I. Striganov, I. S. Tropin, F. Cerutti, L. Esposito, A. Lechner

Abstract: A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3… ▽ More A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3000 fb -1, the peak dose in the innermost magnet insulator ranges from 20 to 35 MGy. Dynamic heat loads to the triplet magnet cold mass are calculated to evaluate the cryogenic capability. In general, FLUKA and MARS results are in a very good agreement. △ Less

Submitted 29 January, 2015; originally announced January 2015.

Comments: 4 pp. Presented paper at the 5th International Particle Accelerator Conference, June 15 -20, 2014, Dresden, Germany

Report number: Fermilab-Conf-14-174-APC

Modelling proton-induced reactions at low energies in the MARS15 code

Authors: Igor L. Rakhno, Nikolai V. Mokhov, Konstantin K. Gudima

Abstract: An implementation of both the ALICE code and TENDL evaluated nuclear data library in order to describe nuclear reactions by low-energy projectiles in the Monte Carlo code MARS15 is presented. Comparisons between results of modelling and experimental data on reaction cross sections and secondary particle distributions are shown as well. An implementation of both the ALICE code and TENDL evaluated nuclear data library in order to describe nuclear reactions by low-energy projectiles in the Monte Carlo code MARS15 is presented. Comparisons between results of modelling and experimental data on reaction cross sections and secondary particle distributions are shown as well. △ Less

Submitted 29 January, 2015; originally announced January 2015.

Comments: 11 pp. Presented at the 12th Meeting on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF-12), April 28-30, 2014, Fermi National Accelerator Laboratory, Batavia, Illinois, USA

Report number: Fermilab-Conf-14-173-APC

Energy deposition studies for the LBNE beam absorber

Authors: Igor L. Rakhno, Nikolai V. Mokhov, Igor S. Tropin

Abstract: Results of detailed Monte Carlo energy deposition studies performed for the LBNE absorber core and the surrounding shielding with the MARS15 code are described. The model of the entire facility, that includes a pion-production target, focusing horns, target chase, decay channel, hadron absorber system -- all with corresponding radiation shielding -- was developed using the recently implemented ROO… ▽ More Results of detailed Monte Carlo energy deposition studies performed for the LBNE absorber core and the surrounding shielding with the MARS15 code are described. The model of the entire facility, that includes a pion-production target, focusing horns, target chase, decay channel, hadron absorber system -- all with corresponding radiation shielding -- was developed using the recently implemented ROOT-based geometry option in the MARS15 code. This option provides substantial flexibility and automation when developing complex geometry models. Both normal operation and accidental conditions were studied. Various design options were considered, in particular the following: (i) filling the decay pipe with air or helium; (ii) the absorber mask material and shape; (iii) the beam spoiler material and size. Results of detailed thermal calculations with the ANSYS code helped to select the most viable absorber design options. △ Less

Submitted 29 January, 2015; originally announced January 2015.

Comments: 8 pp. Presented at the 12th Meeting on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF-12), April 28-30, 2014, Fermi National Accelerator Laboratory, Batavia, Illinois, USA

Report number: Fermilab-Conf-14-172-APC

Storage Ring And Interaction Region Magnets For A μみゅー+μみゅー- Higgs Factory

Authors: A. V. Zlobin, Y. I. Alexahin, V. V. Kappin, V. V. Kashikhin, N. V. Mokhov, S. I. Striganov, I. S. Tropin

Abstract: A low-energy Muon Collider (MC) offers unique opportunities to study the recently found Higgs boson. However, due to a relatively large beam emittance with moderate cooling in this machine, large-aperture high- field superconducting (SC) magnets are required. The magnets need also an adequate margin to operate at a large radiation load from the muon decay showers. General specifications of the SC… ▽ More A low-energy Muon Collider (MC) offers unique opportunities to study the recently found Higgs boson. However, due to a relatively large beam emittance with moderate cooling in this machine, large-aperture high- field superconducting (SC) magnets are required. The magnets need also an adequate margin to operate at a large radiation load from the muon decay showers. General specifications of the SC dipoles and quadrupoles for the 125 GeV c.o.m. Higgs Factory with an average luminosity of ~2x10**31 cm-2s-1 are formulated. Magnet conceptual designs and parameters are reported. The impact of the magnet fringe fields on the beam dynamics as well as the IR and lattice magnet protection from radiation are also reported and discussed. △ Less

Submitted 18 September, 2014; originally announced September 2014.

Comments: 3 p. Presented at North American Particle Accelerator Conference (PAC 2013) Conference

Report number: FERMILAB-CONF-13-411-APC-TD

Reducing backgrounds in the higgs factory muon collider detector

Authors: N. V. Mokhov, S. I. Striganov, I. S. Tropin

Abstract: A preliminary design of the 125 GeV Higgs Factory (HF) Muon Collider (MC) has identified an enormous background loads on the HF detector. This is related to the twelve times higher muon decay probability at HF compared to that previously studied for the 1.5- TeV MC. As a result of MARS15 optimization studies, it is shown that with a carefully designed protection system in the interaction region, i… ▽ More A preliminary design of the 125 GeV Higgs Factory (HF) Muon Collider (MC) has identified an enormous background loads on the HF detector. This is related to the twelve times higher muon decay probability at HF compared to that previously studied for the 1.5- TeV MC. As a result of MARS15 optimization studies, it is shown that with a carefully designed protection system in the interaction region, in the machine-detector interface and inside the detector one can reduce the background rates to a manageable level similar to that achieved for the optimized 1.5-TeV case. The main characteristics of the HF detector background are presented for the configuration found. △ Less

Submitted 5 September, 2014; originally announced September 2014.

Comments: 4 p. 5th International Particle Accelerator Conference (IPAC 2014)

Report number: FERMILAB-CONF-14-184-APC

Hadron Production Model Developments and Benchmarking in the 0.7 - 12 GeV Energy Region

Authors: N. V. Mokhov, K. K. Gudima, S. I. Striganov

Abstract: Driven by the needs of the intensity frontier projects with their Megawatt beams, e.g., ESS, FAIR and Project X, and their experiments, the event generators of the MARS15 code have been recently improved. After thorough analysis and benchmarking against data, including the newest ones by the HARP collaboration, both the exclusive and inclusive particle production models were further developed in t… ▽ More Driven by the needs of the intensity frontier projects with their Megawatt beams, e.g., ESS, FAIR and Project X, and their experiments, the event generators of the MARS15 code have been recently improved. After thorough analysis and benchmarking against data, including the newest ones by the HARP collaboration, both the exclusive and inclusive particle production models were further developed in the crucial for the above projects - but difficult from a theoretical standpoint - projectile energy region of 0.7 to 12 GeV. At these energies, modelling of prompt particle production in nucleon-nucleon and pion-nucleon inelastic reactions is now based on a combination of phase-space and isobar models. Other reactions are still modeled in the framework of the Quark-Gluon String Model. Pion, kaon and strange particle production and propagation in nuclear media are improved. For the alternative inclusive mode, experimental data on large-angle (> 20 degrees) pion production in hadron-nucleus interactions are parameterized in a broad energy range using a two-source model. It is mixed-and-matched with the native MARS model that successfully describes low-angle pion production data. Predictions of both new models are - in most cases - in a good agreement with experimental data obtained at CERN, JINR, LANL, BNL and KEK. △ Less

Submitted 29 August, 2014; originally announced September 2014.

Comments: 11 p

Report number: FERMILAB-CONF-12-638-APC

Beam-Induced Effects and Radiological Issues in High-Intensity High-Energy Fixed Target Experiments

Authors: N. V. Mokhov, S. R. Childress, A. I. Drozhdin, V. S. Pronskikh, D. Reitzner, I. S. Tropin, K. Vaziri

Abstract: The next generation of accelerators for Megawatt proton and heavy-ion beams moves us into a completely new domain of extreme specific energies of up to 0.1 MJ/g (Megajoule/gram) and specific power up to 1 TW/g (Terawatt/gram) in beam interactions with matter. This paper is focused on deleterious effects of controlled and uncontrolled impacts of high-intensity beams on components of beam-lines, tar… ▽ More The next generation of accelerators for Megawatt proton and heavy-ion beams moves us into a completely new domain of extreme specific energies of up to 0.1 MJ/g (Megajoule/gram) and specific power up to 1 TW/g (Terawatt/gram) in beam interactions with matter. This paper is focused on deleterious effects of controlled and uncontrolled impacts of high-intensity beams on components of beam-lines, target stations, beam absorbers, shielding and environment. Two new experiments at Fermilab are taken as an example. The Long-Baseline Neutrino Experiment (LBNE) will explore the interactions and transformations of the world's highest-intensity neutrino beam by sending it from Fermilab more than 1,000 kilometers through the Earth's mantle to a large liquid argon detector. The Mu2e experiment is devoted to studies of the conversion of a negative muon to electron in the field of a nucleus without emission of neutrinos. △ Less

Submitted 29 August, 2014; originally announced September 2014.

Comments: 6 p

Report number: FERMILAB-CONF-12-634-APC

Accelerator System Design, Injection, Extraction and Beam-Material Interaction: Working Group C Summary Report

Authors: N. V. Mokhov, D. Li

Abstract: The performance of high beam power accelerators is strongly dependent on appropriate injection, acceleration and extraction system designs as well as on the way interactions of the beam with machine components are handled. The experience of the previous ICFA High -Brightness Beam workshops has proven that it is quite beneficial to combine analyses and discussion of these issues in one group. A bro… ▽ More The performance of high beam power accelerators is strongly dependent on appropriate injection, acceleration and extraction system designs as well as on the way interactions of the beam with machine components are handled. The experience of the previous ICFA High -Brightness Beam workshops has proven that it is quite beneficial to combine analyses and discussion of these issues in one group. A broad range of topics was presented and discussed at the Working Group C sessions at the HB2012 Workshop. Highlights from the talks, outstanding issues along with plans and proposals for future work are briefly described in this report. △ Less

Submitted 29 August, 2014; originally announced September 2014.

Comments: 6 p

Report number: FERMILAB-CONF-12-637-APC

MARS15 Code Developments Driven by the Intensity Frontier Needs

Authors: N. V. Mokhov, V. S. Pronskikh, I. L. Rakhno, S. I. Striganov, I. S. Tropin, Yu. I. Eidelman, P. Aarnio, K. K. Gudima, A. Yu. Konobeev

Abstract: The MARS15(2012) is the latest version of a multi-purpose Monte-Carlo code developed since 1974 for detailed simulation of hadronic and electromagnetic cascades in an arbitrary 3-D geometry of shielding, accelerator, detector and spacecraft components with energy ranging from a fraction of an electronvolt to 100 TeV. Driven by needs of the intensity frontier projects with their Megawatt beams, e.g… ▽ More The MARS15(2012) is the latest version of a multi-purpose Monte-Carlo code developed since 1974 for detailed simulation of hadronic and electromagnetic cascades in an arbitrary 3-D geometry of shielding, accelerator, detector and spacecraft components with energy ranging from a fraction of an electronvolt to 100 TeV. Driven by needs of the intensity frontier projects with their Megawatt beams, e.g., ESS, FAIR and Project X, the code has been recently substantially improved and extended. These include inclusive and exclusive particle event generators in the 0.7 to 12 GeV energy range, proton inelastic interaction modeling below 20 MeV, implementation of the EGS5 code for electromagnetic shower simulation at energies from 1 keV to 20 MeV, stopping power description in compound materials, new module for DPA calculations for neutrons from a fraction of eV to 20-150 MeV, user-friendly DeTra-based method to calculate nuclide inventories, and new ROOT-based geometry. △ Less

Submitted 29 August, 2014; originally announced September 2014.

Comments: 7 p

Report number: FERMILAB-CONF-12-635-APC

Project X: Physics Opportunities

Authors: Andreas S. Kronfeld, Robert S. Tschirhart, Usama Al-Binni, Wolfgang Altmannshofer, Charles Ankenbrandt, Kaladi Babu, Sunanda Banerjee, Matthew Bass, Brian Batell, David V. Baxter, Zurab Berezhiani, Marc Bergevin, Robert Bernstein, Sudeb Bhattacharya, Mary Bishai, Thomas Blum, S. Alex Bogacz, Stephen J. Brice, Joachim Brod, Alan Bross, Michael Buchoff, Thomas W. Burgess, Marcela Carena, Luis A. Castellanos, Subhasis Chattopadhyay , et al. (111 additional authors not shown)

Abstract: Part 2 of "Project X: Accelerator Reference Design, Physics Opportunities, Broader Impacts". In this Part, we outline the particle-physics program that can be achieved with Project X, a staged superconducting linac for intensity-frontier particle physics. Topics include neutrino physics, kaon physics, muon physics, electric dipole moments, neutron-antineutron oscillations, new light particles, had… ▽ More Part 2 of "Project X: Accelerator Reference Design, Physics Opportunities, Broader Impacts". In this Part, we outline the particle-physics program that can be achieved with Project X, a staged superconducting linac for intensity-frontier particle physics. Topics include neutrino physics, kaon physics, muon physics, electric dipole moments, neutron-antineutron oscillations, new light particles, hadron structure, hadron spectroscopy, and lattice-QCD calculations. Part 1 is available as arXiv:1306.5022 [physics.acc-ph] and Part 3 is available as arXiv:1306.5024 [physics.acc-ph]. △ Less

Submitted 1 October, 2016; v1 submitted 20 June, 2013; originally announced June 2013.

Comments: 209 pp. with many figures; prepared in part for the DPF Community Summer Study; v2 corrects typos (including one author surname), adds an author, and conforms with the version being printed; v3 includes two more chapter authors in full list at the top

Report number: FERMILAB-TM-2557; ANL/PHY-13/2; BNL-101116-2013-BC/81834; JLAB-ACP-13-1725; LBNL-6334E; PNNL-22523; UASLP-IF-13-001; SLAC-R-1029

Optimization of the Target Subsystem for the New g-2 Experiment

Authors: C. Yoshikawa, A. Leveling, N. V. Mokhov, J. Morgan, D. Neuffer, S. Striganov

Abstract: A precision measurement of the muon anomalous magnetic moment, $a_μみゅー = (g-2)/2$, was previously performed at BNL with a result of 2.2 - 2.7 standard deviations above the Standard Model (SM) theoretical calculations. The same experimental apparatus is being planned to run in the new Muon Campus at Fermilab, where the muon beam is expected to have less pion contamination and the extended dataset may… ▽ More A precision measurement of the muon anomalous magnetic moment, $a_μみゅー = (g-2)/2$, was previously performed at BNL with a result of 2.2 - 2.7 standard deviations above the Standard Model (SM) theoretical calculations. The same experimental apparatus is being planned to run in the new Muon Campus at Fermilab, where the muon beam is expected to have less pion contamination and the extended dataset may provide a possible $7.5σしぐま$ deviation from the SM, creating a sensitive and complementary bench mark for proposed SM extensions. We report here on a preliminary study of the target subsystem where the apparatus is optimized for pions that have favorable phase space to create polarized daughter muons around the magic momentum of 3.094 GeV/c, which is needed by the downstream g 2 muon ring. △ Less

Submitted 28 January, 2013; originally announced January 2013.

Comments: 4 pp. 3rd International Particle Accelerator Conference (IPAC 2012) 20-25 May 2012, New Orleans, Louisiana

Report number: FERMILAB-CONF-12-202-AD-APC

Improving the Fermilab Booster Notching Efficiency, Beam Losses and Radiation Levels

Authors: I. L. Rakhno, A. I. Drozhdin, N. V. Mokhov, V. I. Sidorov, I. S. Tropin

Abstract: Currently a fast vertical 1.08-m long kicker (notcher) located in the Fermilab Booster Long-5 straight section is used to remove 3 out of 84 circulating bunches after injection to generate an abort gap. With magnetic field of 72.5 Gauss it removes only 87% of the 3-bunch intensity at 400 MeV, with 75% loss on pole tips of the focusing Booster magnets, 11% on the Long-6 collimators, and 1% in the r… ▽ More Currently a fast vertical 1.08-m long kicker (notcher) located in the Fermilab Booster Long-5 straight section is used to remove 3 out of 84 circulating bunches after injection to generate an abort gap. With magnetic field of 72.5 Gauss it removes only 87% of the 3-bunch intensity at 400 MeV, with 75% loss on pole tips of the focusing Booster magnets, 11% on the Long-6 collimators, and 1% in the rest of the ring. We propose to improve the notching efficiency and reduce beam loss in the Booster by using two horizontal kickers in the Long-12 section. The STRUCT calculations show that using such horizontal notchers, one can remove up to 99% of the 3-bunch intensity at 400-700 MeV, directing 96% of it to a new beam dump at the Long-13 section. This fully decouples notching and collimation. The beam dump absorbs most of the impinging proton energy in its jaws. The latter are encapsulated into an appropriate radiation shielding that reduces impact on the machine components, personnel and environment to the tolerable levels. The MARS simulations show that corresponding prompt and residual radiation levels can be reduced ten times compared to the current ones. △ Less

Submitted 23 January, 2013; originally announced January 2013.

Comments: 4 pp. 3rd International Particle Accelerator Conference (IPAC 2012) 20-25 May 2012. New Orleans, Louisiana

Report number: FERMILAB-CONF-12-154-AD-APC

Journal ref: Conf.Proc. C1205201 (2012) 562-564

Overview of the LBNE Neutrino Beam

Authors: C. D. Moore, Yun He, Patrick Hurh, James Hylen, Byron Lundberg, Mike McGee, Joel Misek, Nikolai V. Mokhov, Vaia Papadimitriou, Rob Plunkett, Ryan Schultz, Gueorgui Velev, Karlton Williams, Robert Miles Zwaska

Abstract: The Long Baseline Neutrino Experiment (LBNE) will utilize a neutrino beamline facility located at Fermilab. The facility is designed to aim a beam of neutrinos toward a detector placed at the Deep Underground Science and Engineering Laboratory (DUSEL) in South Dakota. The neutrinos are produced in a three-step process. First, protons from the Main Injector hit a solid target and produce mesons. Th… ▽ More The Long Baseline Neutrino Experiment (LBNE) will utilize a neutrino beamline facility located at Fermilab. The facility is designed to aim a beam of neutrinos toward a detector placed at the Deep Underground Science and Engineering Laboratory (DUSEL) in South Dakota. The neutrinos are produced in a three-step process. First, protons from the Main Injector hit a solid target and produce mesons. Then, the charged mesons are focused by a set of focusing horns into the decay pipe, towards the far detector. Finally, the mesons that enter the decay pipe decay into neutrinos. The parameters of the facility were determined by an amalgam of the physics goals, the Monte Carlo modeling of the facility, and the experience gained by operating the NuMI facility at Fermilab. The initial beam power is expected to be ~700 kW, however some of the parameters were chosen to be able to deal with a beam power of 2.3 MW. △ Less

Submitted 11 September, 2012; originally announced September 2012.

Comments: 3 pp. Particle Accelerator, 24th Conference (PAC'11) 2011. 28 Mar - 1 Apr 2011. New York, USA

Report number: FERMILAB-CONF-11-086-AD

Calculation of Residual Dose Around Small Objects Using Mu2e Target as an Example

Authors: V. S. Pronskikh, A. F. Leveling, N. V. Mokhov, I. L. Rakhno, P. Aarnio

Abstract: The MARS15 code provides contact residual dose rates for relatively large accelerator and experimental components for predefined irradiation and cooling times. The dose rate at particular distances from the components, some of which can be rather small in size, is calculated in a post Monte-Carlo stage via special algorithms described elsewhere. The approach is further developed and described in t… ▽ More The MARS15 code provides contact residual dose rates for relatively large accelerator and experimental components for predefined irradiation and cooling times. The dose rate at particular distances from the components, some of which can be rather small in size, is calculated in a post Monte-Carlo stage via special algorithms described elsewhere. The approach is further developed and described in this paper. △ Less

Submitted 1 May, 2012; originally announced May 2012.

Comments: 7 pp

Report number: FERMILAB-FN-0930-APC

Detector Background at Muon Colliders

Authors: N. V. Mokhov, S. I. Striganov

Abstract: Physics goals of a Muon Collider (MC) can only be reached with appropriate design of the ring, interaction region (IR), high-field superconducting magnets, machine -detector interface (MDI) and detector. Results of the most recent realistic simulation studies are presented for a 1.5-TeV MC. It is shown that appropriately designed IR and MDI with sophisticated shielding in the detector have a poten… ▽ More Physics goals of a Muon Collider (MC) can only be reached with appropriate design of the ring, interaction region (IR), high-field superconducting magnets, machine -detector interface (MDI) and detector. Results of the most recent realistic simulation studies are presented for a 1.5-TeV MC. It is shown that appropriately designed IR and MDI with sophisticated shielding in the detector have a potential to substantially suppress the background rates in the MC detector. The main characteristics of backgrounds are studied. △ Less

Submitted 30 April, 2012; originally announced April 2012.

Comments: 8 pp. 2nd International Conference on Technology and Instrumentation in Particle Physics 2011: TIPP 2011, 9-14 Jun 2011: Chicago, Illinois

Report number: FERMILAB-PUB-11-483-APC

Muon Collider Machine-Detector Interface

Authors: Nikolai V. Mokhov

Abstract: The deleterious effects of the background and radiation environment produced by the decaying muon beam are studied in the Muon Collider Interaction Region, detector and Machine-Detector Interface designs. The deleterious effects of the background and radiation environment produced by the decaying muon beam are studied in the Muon Collider Interaction Region, detector and Machine-Detector Interface designs. △ Less

Submitted 26 April, 2012; originally announced April 2012.

Comments: 6 pp

Report number: FERMILAB-PUB-11-535-APC

Journal ref: ICFA Beam Dyn.Newslett. 55 (2011) 79-84

Muon collider interaction region design

Authors: Y. I. Alexahin, E. Gianfelice-Wendt, V. V. Kashikhin, N. V. Mokhov, A. V. Zlobin, V. Y. Alexakhin

Abstract: Design of a muon collider interaction region (IR) presents a number of challenges arising from low βべーた* < 1 cm, correspondingly large beta-function values and beam sizes at IR magnets, as well as the necessity to protect superconducting magnets and collider detectors from muon decay products. As a consequence, the designs of the IR optics, magnets and machine-detector interface are strongly interlac… ▽ More Design of a muon collider interaction region (IR) presents a number of challenges arising from low βべーた* < 1 cm, correspondingly large beta-function values and beam sizes at IR magnets, as well as the necessity to protect superconducting magnets and collider detectors from muon decay products. As a consequence, the designs of the IR optics, magnets and machine-detector interface are strongly interlaced and iterative. A consistent solution for the 1.5 TeV c.o.m. muon collider IR is presented. It can provide an average luminosity of 1034 cm-2s-1 with an adequate protection of magnet and detector components. △ Less

Submitted 25 April, 2012; originally announced April 2012.

Comments: 7 pp

Report number: FERMILAB-PUB-11-370-APC

Journal ref: Phys.Rev.ST Accel.Beams 14 (2011) 061001

Radiation effects in a muon collider ring and dipole magnet protection

Authors: N. V. Mokhov, V. V. Kashikhin, I. Novitski, A. V. Zlobin

Abstract: The requirements and operating conditions for a Muon Collider Storage Ring (MCSR) pose significant challenges to superconducting magnets. The dipole magnets should provide a high magnetic field to reduce the ring circumference and thus maximize the number of muon collisions during their lifetime. One third of the beam energy is continuously deposited along the lattice by the decay electrons at the… ▽ More The requirements and operating conditions for a Muon Collider Storage Ring (MCSR) pose significant challenges to superconducting magnets. The dipole magnets should provide a high magnetic field to reduce the ring circumference and thus maximize the number of muon collisions during their lifetime. One third of the beam energy is continuously deposited along the lattice by the decay electrons at the rate of 0.5 kW/m for a 1.5-TeV c.o.m. and a luminosity of 1034 cm-2s-1. Unlike dipoles in proton machines, the MCSR dipoles should allow this dynamic heat load to escape the magnet helium volume in the horizontal plane, predominantly towards the ring center. This paper presents the analysis and comparison of radiation effects in MCSR based on two dipole magnets designs. Tungsten masks in the interconnect regions are used in both cases to mitigate the unprecedented dynamic heat deposition and radiation in the magnet coils. △ Less

Submitted 23 February, 2012; originally announced February 2012.

Comments: 3 pp. Particle Accelerator, 24th Conference (PAC'11) 28 Mar - 1 Apr 2011: New York, USA

Report number: FERMILAB-CONF-11-095-APC

Muon Collider interaction region and machine-detector interface design

Authors: N. V. Mokhov, Y. I. Alexahin, V. V. Kashikhin, S. I. Striganov, A. V. Zlobin

Abstract: One of the key systems of a Muon Collider (MC) - seen as the most exciting option for the energy frontier machine in the post-LHC era - is its interaction region (IR). Designs of its optics, magnets and machine-detector interface are strongly interlaced and iterative. As a result of recent comprehensive studies, consistent solutions for the 1.5-TeV c.o.m. MC IR have been found and are described he… ▽ More One of the key systems of a Muon Collider (MC) - seen as the most exciting option for the energy frontier machine in the post-LHC era - is its interaction region (IR). Designs of its optics, magnets and machine-detector interface are strongly interlaced and iterative. As a result of recent comprehensive studies, consistent solutions for the 1.5-TeV c.o.m. MC IR have been found and are described here. To provide the required momentum acceptance, dynamic aperture and chromaticity, an innovative approach was used for the IR optics. Conceptual designs of large-aperture high-field dipole and high-gradient quadrupole magnets based on Nb3Sn superconductor were developed and analyzed in terms of the operating margin, field quality, mechanics, coil cooling and quench protection. Shadow masks in the interconnect regions and liners inside the magnets are used to mitigate the unprecedented dynamic heat deposition due to muon decays (~0.5 kW/m). It is shown that an appropriately designed machine-detector interface (MDI) with sophisticated shielding in the detector has a potential to substantially suppress the background rates in the MC detector. △ Less

Submitted 17 February, 2012; originally announced February 2012.

Comments: 3 pp. Particle Accelerator, 24th Conference (PAC'11) 28 Mar - 1 Apr 2011: New York, USA

Report number: FERMILAB-CONF-11-094-APC

Radiation and thermal analysis of production solenoid for Mu2e experimental setup

Authors: V. S. Pronskikh, V. V. Kashikhin, N. V. Mokhov

Abstract: The Muon-to-Electron (Mu2e) experiment at Fermilab, will seek the evidence of direct muon to electron conversion at the sensitivity level where it cannot be explained by the Standard Model. An 8-GeV 25-kW proton beam will be directed onto a tilted gold target inside a large-bore superconducting Production Solenoid (PS) with the peak field on the axis of ~5T. The negative muons resulting from the p… ▽ More The Muon-to-Electron (Mu2e) experiment at Fermilab, will seek the evidence of direct muon to electron conversion at the sensitivity level where it cannot be explained by the Standard Model. An 8-GeV 25-kW proton beam will be directed onto a tilted gold target inside a large-bore superconducting Production Solenoid (PS) with the peak field on the axis of ~5T. The negative muons resulting from the pion decay will be captured in the PS aperture and directed by an S-shaped Transport Solenoid towards the stopping target inside the Detector Solenoid. In order for the superconducting magnets to operate reliably and with a sufficient safety margin, the peak neutron flux entering the coils must be reduced by 3 orders of magnitude that is achieved by means of a sophisticated absorber placed in the magnet aperture. The proposed absorber, consisting of W- and Cu-based alloy parts, is optimized for the performance and cost. Results of MARS15 simulations of energy deposition and radiation are reported. The results of the PS magnet thermal analysis, coordinated with the coil cooling scheme, are reported as well for the selected absorber design. △ Less

Submitted 17 February, 2012; originally announced February 2012.

Comments: 4 pp. Particle Accelerator, 24th Conference (PAC'11) 28 Mar - 1 Apr 2011: New York, USA

Report number: FERMILAB-CONF-11-125-APC

Optimization of a Mu2e production solenoid heat and radiation shield using MARS15

Authors: V. S. Pronskikh, N. V. Mokhov

Abstract: A Monte-Carlo study of several Mu2e Production Solenoid (PS) absorber (heat shield) versions using the MARS15 code has been performed. Optimizations for material as well as cost (amount of tungsten) have been carried out. Studied are such quantities as the number of displacements per atom (DPA) in the helium-cooled solenoid superconducting coils, power density and dynamic heat load in various part… ▽ More A Monte-Carlo study of several Mu2e Production Solenoid (PS) absorber (heat shield) versions using the MARS15 code has been performed. Optimizations for material as well as cost (amount of tungsten) have been carried out. Studied are such quantities as the number of displacements per atom (DPA) in the helium-cooled solenoid superconducting coils, power density and dynamic heat load in various parts of the PS and its surrounding structures. Prompt dose, residual dose, secondary particle flux are also simulated in the PS structures and the experimental hall. A preliminary choice of the PS absorber design is made on the ground of these studies. △ Less

Submitted 17 February, 2012; originally announced February 2012.

Comments: 7 pp. 20th International Baldin Seminar on High Energy Physics Problems: Relativistic Nuclear Physics and Quantum Chromodynamics (ISHEPP 2010) 4-9 Oct 2010: Dubna, Russia

Report number: FERMILAB-CONF-11-024-APC

Summary of working group g: beam material interaction

Authors: D. Kiselev, N. V. Mokhov, R. Schmidt

Abstract: For the first time, the workshop on High-Intensity and High-Brightness Hadron Beams (HB2010), held at Morschach, Switzerland and organized by the Paul Scherrer Institute, included a Working group dealing with the interaction between beam and material. Due to the high power beams of existing and future facilities, this topic is already of great relevance for such machines and is expected to become… ▽ More For the first time, the workshop on High-Intensity and High-Brightness Hadron Beams (HB2010), held at Morschach, Switzerland and organized by the Paul Scherrer Institute, included a Working group dealing with the interaction between beam and material. Due to the high power beams of existing and future facilities, this topic is already of great relevance for such machines and is expected to become even more important in the future. While more specialized workshops related to topics of radiation damage, activation or thermo - mechanical calculations, already exist, HB2010 provided the occasion to discuss the interplay of these topics, focusing on components like targets, beam dumps and collimators, whose reliability are crucial for a user facility. In addition, a broader community of people working on a variety of issues related to the operation of accelerators could be informed and their interest sparked. △ Less

Submitted 16 February, 2012; originally announced February 2012.

Comments: 3 pp. 46th ICFA Advanced Beam Dynamics Workshop HB2010, Sep 27 - Oct 1 2010: Morschach, Switzerland

Report number: FERMILAB-CONF-10-481-APC

Recent MARS15 developments: nuclide inventory, DPA and gas production

Authors: N. V. Mokhov

Abstract: Recent developments in the MARS15 code are described for the critical modules related to demands of hadron and lepton colliders and Megawatt proton and heavy-ion beam facilities. Details of advanced models for particle production and nuclide distributions in nuclear interactions at low and medium energies, energy loss, atomic displacements and gas production are presented along with benchmarking a… ▽ More Recent developments in the MARS15 code are described for the critical modules related to demands of hadron and lepton colliders and Megawatt proton and heavy-ion beam facilities. Details of advanced models for particle production and nuclide distributions in nuclear interactions at low and medium energies, energy loss, atomic displacements and gas production are presented along with benchmarking against data. △ Less

Submitted 10 February, 2012; originally announced February 2012.

Comments: 5 pp. 46th ICFA Advanced Beam Dynamics Workshop HB2010, Sep 27 - Oct 1 2010: Morschach, Switzerland

Report number: FERMILAB-CONF-10-518-APC

New Parallel computing framework for radiation transport codes

Authors: M. A. Kostin, N. V. Mokhov, K. Niita

Abstract: A new parallel computing framework has been developed to use with general-purpose radiation transport codes. The framework was implemented as a C++ module that uses MPI for message passing. The module is significantly independent of radiation transport codes it can be used with, and is connected to the codes by means of a number of interface functions. The frame work was integrated with the MARS15… ▽ More A new parallel computing framework has been developed to use with general-purpose radiation transport codes. The framework was implemented as a C++ module that uses MPI for message passing. The module is significantly independent of radiation transport codes it can be used with, and is connected to the codes by means of a number of interface functions. The frame work was integrated with the MARS15 code, and an effort is under way to deploy it in PHITS. Besides the parallel computing functionality, the framework offers a checkpoint facility that allows restarting calculations with a saved checkpoint file. The checkpoint facility can be used in single process calculations as well as in the parallel regime. Several checkpoint files can be merged into one thus combining results of several calculations. The framework also corrects some of the known problems with the sch eduling and load balancing found in the original implementations of the parallel computing functionality in MARS15 and PHITS. The framework can be used efficiently on homogeneous systems and networks of workstations, where the interference from the other users is possible. △ Less

Submitted 9 February, 2012; originally announced February 2012.

Comments: 6 pp. Joint International Conference on Supercomputing in Nuclear Applications and Monte Carlo SNA + MC2010, 17-21 Oct 2010: Tokyo, Japan

Report number: FERMILAB-CONF-10-348-APC

JASMIN: Japanese-American study of muon interactions and neutron detection

Authors: Hiroshi Nakashima, N. V. Mokhov, Yoshimi Kasugai, Norihiro Matsuda, Yosuke Iwamoto, Yukio Sakamoto, Anthony F. Leveling, David J. Boehnlein, Kamran Vaziri, Hiroshi Matsumura, Masayuki Hagiwara, Hiroshi Iwase, Syuichi Ban, Hideo Hirayama, Takashi Nakamura, Koji Oishi, Nobuhiro Shigyo, Hiroyuki Arakawa, Tsuyoshi Kajimoto, Kenji Ishibashi, Hiroshi Yashima, Shun Sekimoto, Norikazu Kinoshita, Hee-Seock Lee, Koji Niita

Abstract: Experimental studies of shielding and radiation effects at Fermi National Accelerator Laboratory (FNAL) have been carried out under collaboration between FNAL and Japan, aiming at benchmarking of simulation codes and study of irradiation effects for upgrade and design of new high-energy accelerator facilities. The purposes of this collaboration are (1) acquisition of shielding data in a proton bea… ▽ More Experimental studies of shielding and radiation effects at Fermi National Accelerator Laboratory (FNAL) have been carried out under collaboration between FNAL and Japan, aiming at benchmarking of simulation codes and study of irradiation effects for upgrade and design of new high-energy accelerator facilities. The purposes of this collaboration are (1) acquisition of shielding data in a proton beam energy domain above 100 GeV; (2) further evaluation of predictive accuracy of the PHITS and MARS codes; (3) modification of physics models and data in these codes if needed; (4) establishment of irradiation field for radiation effect tests; and (5) development of a code module for improved description of radiation effects. A series of experiments has been performed at the Pbar target station and NuMI facility, using irradiation of targets with 120 GeV protons for antiproton and neutrino production, as well as the M-test beam line (M-test) for measuring nuclear data and detector responses. Various nuclear and shielding data have been measured by activation methods with chemical separation techniques as well as by other detectors such as a Bonner ball counter. Analyses with the experimental data are in progress for benchmarking the PHITS and MARS15 codes. In this presentation recent activities and results are reviewed. △ Less

Submitted 9 February, 2012; originally announced February 2012.

Comments: 15 pp. 10th Meeting of the Task-Force on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF10), 2-4 Jun 2010: Geneva, Switzerland

Report number: FERMILAB-CONF-10-330-APC

Neutron energy spectrum from 120 GeV protons on a thick copper target

Authors: Nobuhiro Shigyo, Toshiya Sanami, Tsuyoshi Kajimoto, Yosuke Iwamoto, Masayuki Hagiwara, Kiwamu Saito, Kenji Ishibashi, Hiroshi Nakashima, Yukio Sakamoto, Hee-Seock Lee, Erik Ramberg, Aria A. Meyhoefer, Rick Coleman, Doug Jensen, Anthony F. Leveling, David J. Boehnlein, Nikolai V. Mokhov

Abstract: Neutron energy spectrum from 120 GeV protons on a thick copper target was measured at the Meson Test Beam Facility (MTBF) at Fermi National Accelerator Laboratory. The data allows for evaluation of neutron production process implemented in theoretical simulation codes. It also helps exploring the reasons for some disagreement between calculation results and shielding benchmark data taken at high e… ▽ More Neutron energy spectrum from 120 GeV protons on a thick copper target was measured at the Meson Test Beam Facility (MTBF) at Fermi National Accelerator Laboratory. The data allows for evaluation of neutron production process implemented in theoretical simulation codes. It also helps exploring the reasons for some disagreement between calculation results and shielding benchmark data taken at high energy accelerator facilities, since it is evaluated separately from neutron transport. The experiment was carried out using a 120 GeV proton beam of 3E5 protons/spill. Since the spill duration was 4 seconds, proton-induced events were counted pulse by pulse. The intensity was maintained using diffusers and collimators installed in the beam line to MTBF. The protons hit a copper block target the size of which is 5cm x 5cm x 60 cm long. The neutrons produced in the target were measured using NE213 liquid scintillator detectors, placed about 5.5 m away from the target at 30^{\circ} and 5 m 90^{\circ} with respect to the proton beam axis. The neutron energy was determined by time-of-flight technique using timing difference between the NE213 and a plastic scintillator located just before the target. Neutron detection efficiency of NE213 was determined on basis of experimental data from the high energy neutron beam line at Los Alamos National Laboratory. The neutron spectrum was compared with the results of multi-particle transport codes to validate the implemented theoretical models. The apparatus would be applied to future measurements to obtain a systematic data set for secondary particle production on various target materials. △ Less

Submitted 7 February, 2012; originally announced February 2012.

Comments: 10 pp. 10th Meeting of the Task-Force on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF10) 2-4 Jun 2010: Geneva, Switzerland

Report number: FERMILAB-CONF-10-331-APC

Dealing with megawatt beams

Authors: N. V. Mokhov

Abstract: The next generation of accelerators for MegaWatt proton, electron and heavy-ion beams puts unprecedented requirements on the accuracy of particle production predictions, the capability and reliability of the codes used in planning new accelerator facilities and experiments, the design of machine, target and collimation systems, detectors and radiation shielding and minimization of their impact on… ▽ More The next generation of accelerators for MegaWatt proton, electron and heavy-ion beams puts unprecedented requirements on the accuracy of particle production predictions, the capability and reliability of the codes used in planning new accelerator facilities and experiments, the design of machine, target and collimation systems, detectors and radiation shielding and minimization of their impact on environment. Recent advances in code developments are described for the critical modules related to these challenges. Examples are given for the most demanding areas: targets, collimators, beam absorbers, radiation shielding, induced radioactivity and radiation damage. △ Less

Submitted 7 February, 2012; originally announced February 2012.

Comments: 10 pp. 10th Meeting of the Task-Force on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF10) 2-4 Jun 2010: Geneva, Switzerland

Report number: FERMILAB-CONF-10-329-APC

120-mm superconducting quadrupole for interaction regions of hadron colliders

Authors: A. V. Zlobin, V. V. Kashikhin, N. V. Mokhov, I. Novitski

Abstract: Magnetic and mechanical designs of a Nb3Sn quadrupole magnet with 120-mm aperture suitable for interaction regions of hadron colliders are presented. The magnet is based on a two-layer shell-type coil and a cold iron yoke. Special spacers made of a low-Z material are implemented in the coil mid-planes to reduce the level of radiation heat deposition and radiation dose in the coil. The quadrupole m… ▽ More Magnetic and mechanical designs of a Nb3Sn quadrupole magnet with 120-mm aperture suitable for interaction regions of hadron colliders are presented. The magnet is based on a two-layer shell-type coil and a cold iron yoke. Special spacers made of a low-Z material are implemented in the coil mid-planes to reduce the level of radiation heat deposition and radiation dose in the coil. The quadrupole mechanical structure is based on aluminum collars supported by an iron yoke and a stainless steel skin. Magnet parameters including maximum field gradient and field harmonics, Nb3Sn coil pre-stress and protection at the operating temperatures of 4.5 and 1.9 K are reported. The level and distribution of radiation heat deposition in the coil and other magnet components are discussed. △ Less

Submitted 1 February, 2012; originally announced February 2012.

Comments: 3 pp. 1st International Particle Accelerator Conference: IPAC'10, 23-28 May 2010: Kyoto, Japan

Report number: FERMILAB-CONF-10-133-APC-TD

Magnet designs for muon collider ring and interactions regions

Authors: A. V. Zlobin, Y. I. Alexahin, V. V. Kashikhin, N. V. Mokhov

Abstract: Conceptual designs of superconducting magnets for the storage ring of a Muon Collider with a 1.5 TeV c.o.m. energy and an average luminosity of 10 34 cm-2s-1 are presented. All magnets are based on Nb3Sn superconductor and designed to provide an adequate operating field/field gradient in the aperture with the critical current margin required for reliable magnet operation in the machine. Magnet cro… ▽ More Conceptual designs of superconducting magnets for the storage ring of a Muon Collider with a 1.5 TeV c.o.m. energy and an average luminosity of 10 34 cm-2s-1 are presented. All magnets are based on Nb3Sn superconductor and designed to provide an adequate operating field/field gradient in the aperture with the critical current margin required for reliable magnet operation in the machine. Magnet cross-sections were optimized to achieve the accelerator field quality in the magnet aperture occupied with beams. The magnets and corresponding protective measures are designed to handle about 0.5 kW/m of dynamic heat load from the muon beam decays. Magnet parameters are reported and compared with the requirements. △ Less

Submitted 1 February, 2012; originally announced February 2012.

Comments: 3 pp. 1st International Particle Accelerator Conference: IPAC'10, 23-28 May 2010: Kyoto, Japan

Report number: FERMILAB-CONF-10-132-APC-TD