-
High Gradient Testing of off-Axis Coupled C-band Cu and CuAg Accelerating Structures
Authors:
Mitchell Schneider,
Muhammed Zuboraj,
Valery Dolgashev,
John J Lewellen,
Sami G Tantawi,
Ryan Fleming,
Dmitry Gorelov,
Mark Middendorf,
Emilio A Nanni,
Evgenya I Simakov
Abstract:
We report the results of high gradient testing of two single cell off axis coupled standing wave accelerating structures. Two brazed standing wave side coupled structures with the same geometry were tested one made of pure copper Cu and one made of a copper silver CuAg alloy with silver concentration of 0.08 percent. A peak surface electric field of 450 MV per m was achieved in the CuAg structure…
▽ More
We report the results of high gradient testing of two single cell off axis coupled standing wave accelerating structures. Two brazed standing wave side coupled structures with the same geometry were tested one made of pure copper Cu and one made of a copper silver CuAg alloy with silver concentration of 0.08 percent. A peak surface electric field of 450 MV per m was achieved in the CuAg structure for a klystron input power of 14.5 MW and a 1 mirco s pulse length which was 25 percent higher than the peak surface electric field achieved in the Cu structure. The superb high gradient performance was achieved because of the two major optimizations in the cavity geometry 1 the shunt impedance of the cavity was maximized for a peak surface electric field to accelerating gradient ratio of 2 for a fully relativistic particle 2 the peak magnetic field enhancement due to the input coupler was minimized to limit pulse heating. These tests allow us to conclude that C band accelerating structures can operate at peak fields similar to those at higher frequencies while providing a larger beam iris for improved beam transport.
△ Less
Submitted 30 October, 2022;
originally announced October 2022.
-
Transformative Technology for FLASH Radiation Therapy: A Snowmass 2021 White Paper
Authors:
Salime Boucher,
Eric Esarey,
Cameron Geddes,
Carol Johnstone,
Sergey Kutsaev,
Billy W. Loo Jr,
Francois Méot,
Brahim Mustapha,
Kei Nakamura,
Emilio Nanni,
Lieselotte Obst-Huebl,
Stephen E. Sampayan,
Carl Schroeder,
Reinhard Schulte,
Ke Sheng,
Antoine Snijders,
Emma Snively,
Sami G. Tantawi,
Jeroen van Tilborg
Abstract:
Conventional cancer therapies include surgery, radiation therapy, chemotherapy, and, more recently, immunotherapy. These modalities are often combined to improve the therapeutic index. The general concept of radiation therapy is to increase the therapeutic index by creating a physical dose differential between tumors and normal tissues through precision dose targeting, image guidance, and high rad…
▽ More
Conventional cancer therapies include surgery, radiation therapy, chemotherapy, and, more recently, immunotherapy. These modalities are often combined to improve the therapeutic index. The general concept of radiation therapy is to increase the therapeutic index by creating a physical dose differential between tumors and normal tissues through precision dose targeting, image guidance, and high radiation beams that deliver radiation dose with high conformality, e.g., protons and ions. However, treatment and cure are still limited by normal tissue radiation toxicity, with many patients experiencing acute and long-term side effects. Recently, however, a fundamentally different paradigm for increasing the therapeutic index of radiation therapy has emerged, supported by preclinical research, and based on the FLASH radiation effect. FLASH radiation therapy (FLASH-RT) is an ultra-high dose-rate delivery of a therapeutic radiation dose within a fraction of a second. Experimental studies have shown that normal tissues seem to be universally spared at these high dose rates, whereas tumors are not. The dose delivery conditions are not yet fully characterized. Still, it is currently estimated that large doses of 10 Gy or more delivered in 200 ms or less produce normal tissue sparing effects yet effectively kill tumor cells. There is a great opportunity, but also many technical challenges, for the accelerator community to create the required dose rates with novel and compact accelerators to ensure the safe delivery of FLASH radiation beams.
△ Less
Submitted 21 March, 2022;
originally announced March 2022.
-
An Advanced NCRF Linac Concept for a High Energy e$^+$e$^-$ Linear Collider
Authors:
Karl L. Bane,
Timothy L. Barklow,
Martin Breidenbach,
Craig P. Burkhart,
Eric A. Fauve,
Alysson R. Gold,
Vincent Heloin,
Zenghai Li,
Emilio A. Nanni,
Mamdouh Nasr,
Marco Oriunno,
James McEwan Paterson,
Michael E. Peskin,
Tor O. Raubenheimer,
Sami G. Tantawi
Abstract:
We have explored a concept for an advanced Normal-Conducting Radio-Frequency (NCRF) C-band linear accelerator (linac) structure to achieve a high gradient, high power e$^+$e$^-$ linear collider in the TeV class. This design study represents the first comprehensive investigation for an emerging class of distributed coupling accelerator topology exploring nominal cavity geometries, frequency and tem…
▽ More
We have explored a concept for an advanced Normal-Conducting Radio-Frequency (NCRF) C-band linear accelerator (linac) structure to achieve a high gradient, high power e$^+$e$^-$ linear collider in the TeV class. This design study represents the first comprehensive investigation for an emerging class of distributed coupling accelerator topology exploring nominal cavity geometries, frequency and temperature of operation. The structure features internal manifolds for distributing RF power separately to each cell, permitting the full structure geometry to be designed for high shunt impedance and low breakdown. Optimized within operational constraints, we find that it is advantageous for the structure to be cooled directly by liquid nitrogen (LN), further increasing the shunt impedance. A crucial part of this design process has been cost optimization, which is largely driven by the cost of peak RF power. The first operation of a distributed coupling structure at cryogenic temperatures and the nominal operating gradient 120 MeV/m is also presented, demonstrating the feasibility of achieving high-gradient performance with a cryogenically-cooled normal-conducting accelerating structure.
△ Less
Submitted 7 April, 2019; v1 submitted 26 July, 2018;
originally announced July 2018.
-
Transverse Impedance Bench Measurements in NLC/JLC Accelerating Structures
Authors:
N. Baboi,
G. B. Bowden,
R. M. Jones,
S. G. Tantawi,
J. R. Lewandowski
Abstract:
The wire method is a more rapid and less costly method to measure impedances of RF components compared to methods using a beam. A setup using a single displaced wire to excite and measure transverse resonant modes in accelerating structures for the Next Linear Collider/ Japanese Linear Collider (NLC/JLC) has been built. The RF signal is coupled into and out of the structure using two matching se…
▽ More
The wire method is a more rapid and less costly method to measure impedances of RF components compared to methods using a beam. A setup using a single displaced wire to excite and measure transverse resonant modes in accelerating structures for the Next Linear Collider/ Japanese Linear Collider (NLC/JLC) has been built. The RF signal is coupled into and out of the structure using two matching sections with a broadband frequency from 11 to 18 GHz. Their contribution to the scattering parameter is minimized by a calibration technique. A standing wave structure has been measured. Difficulties in accurately predicting the modal loss factors were encountered related to the approximations made and to experimental issues. The measurements are presented and comparisons with simulations are made.
△ Less
Submitted 23 May, 2003;
originally announced May 2003.
-
Impedance Measurement Setup for Higher-Order Mode Studies in NLC Accelerator Structures with the Wire Method
Authors:
N. Baboi,
R. M. Jones,
J. W. Wang,
G. B. Bowden,
V. A. Dolgashev,
J. Lewandowski,
S. G. Tantawi,
P. B. Wilson
Abstract:
Dipole modes are the main cause of transverse emittance dilution in the Japanese Linear Collider / Next Linear Collider (JLC/NLC). A diagnostic setup has been built in order to investigate them. The method is based on using a coaxial wire to excite and measure electromagnetic modes of accelerating structures. This method can offer a more efficient and less expensive procedure than the ASSET faci…
▽ More
Dipole modes are the main cause of transverse emittance dilution in the Japanese Linear Collider / Next Linear Collider (JLC/NLC). A diagnostic setup has been built in order to investigate them. The method is based on using a coaxial wire to excite and measure electromagnetic modes of accelerating structures. This method can offer a more efficient and less expensive procedure than the ASSET facility. Initial measurements have been made and are presented in this paper.
△ Less
Submitted 19 September, 2002;
originally announced September 2002.
-
A Resonant Cavity for Single-Shot Emittance Measurement
Authors:
J. S. Kim,
C. D. Nantista,
D. H. Whittum,
R. H. Miller,
S. G. Tantawi,
A. W. Weidemann
Abstract:
We present a non-invasive, resonant cavity based approach to beam emittance measurement of a shot-to-shot non-circular beam pulse of multi-bunches. In a resonant cavity, desired field components can be enhanced up to Q_L_lambda/pi, where Q_L_lambda is the loaded Q of the resonance mode lambda, when the cavity resonant mode matches with the beam operating frequency. In particular, a Quad-cavity,…
▽ More
We present a non-invasive, resonant cavity based approach to beam emittance measurement of a shot-to-shot non-circular beam pulse of multi-bunches. In a resonant cavity, desired field components can be enhanced up to Q_L_lambda/pi, where Q_L_lambda is the loaded Q of the resonance mode lambda, when the cavity resonant mode matches with the beam operating frequency. In particular, a Quad-cavity, with its quadrupole mode at beam operating frequency, extracts the beam quad-moment exclusively, utilizing the symmetry of the cavity and some simple networks to suppress common modes. Six successive beam quadrupole moment measurements, performed at different betatron phases in a linear transport system, allow us to determine the beam emittance, i.e., the beam size and shape in the beam's phase space. One measurement alone provides the rms-beam size if the beam position is given, for instance, by nearby beam-position-monitors. This paper describes the basic design and analysis of a Quad-cavity beam monitoring system.
△ Less
Submitted 18 September, 2002;
originally announced September 2002.
-
A Multi-Moded RF Delay Line Distribution System for the Next Linear Collider
Authors:
S. G. Tantawi,
C. Nantista,
N. Kroll,
Z. Li,
R. Miller,
R. Ruth,
P. Wilson,
J. Neilson
Abstract:
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is comb…
▽ More
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is combined into a single waveguide delay line using a multi-mode launcher. The output mode of the launcher is determined by the phase coding of the input signals. The combined power is extracted from the delay line using mode-selective extractors, each of which extracts a single mode. Hence, the phase coding of the sources controls the output port of the combined power. The power is then fed to the local accelerator structures. We present a detailed design of such a system, including several implementation methods for the launchers, extractors, and ancillary high power rf components. The system is designed so that it can handle the 600 MW peak power required by the NLC design while maintaining high efficiency.
△ Less
Submitted 17 September, 2002;
originally announced September 2002.
-
Coaxial Wire Measurements In NLC Accelerating Structures
Authors:
N. Baboi,
R. M. Jones,
G. B. Bowden,
V. Dolgashev,
S. G. Tantawi,
J. W. Wang
Abstract:
The coaxial wire method provides an experimental way of measuring wake fields without the need for a particle beam. A special setup has been designed and is in the process of being fabricated at SLAC to measure the loss factors and synchronous frequencies of dipole modes in both traveling and standing wave structures for the Next Linear Collider (NLC). The method is described and predictions bas…
▽ More
The coaxial wire method provides an experimental way of measuring wake fields without the need for a particle beam. A special setup has been designed and is in the process of being fabricated at SLAC to measure the loss factors and synchronous frequencies of dipole modes in both traveling and standing wave structures for the Next Linear Collider (NLC). The method is described and predictions based on electromagnetic field simulations are discussed
△ Less
Submitted 27 June, 2002;
originally announced June 2002.
-
A Compact, Planar, Eight-Port Waveguide Power Divider/Combiner: The Cross Potent Superhybrid
Authors:
Christopher D. Nantista,
Sami G. Tantawi
Abstract:
In this letter, we present a novel four-way divider/combiner in rectangular waveguide. The design is completely two-dimensional in the h-plane, with eight-fold mirror symmetry, and is based on a recent four-port hybrid design [6]. In combining mode, it can function as a phased array with four inputs and four outputs. The planar nature of this design provides advantages, such as the freedom to in…
▽ More
In this letter, we present a novel four-way divider/combiner in rectangular waveguide. The design is completely two-dimensional in the h-plane, with eight-fold mirror symmetry, and is based on a recent four-port hybrid design [6]. In combining mode, it can function as a phased array with four inputs and four outputs. The planar nature of this design provides advantages, such as the freedom to increase the waveguide height beyond the over-moding limit in order to reduce field strengths. Along with its open geometry, this makes it ideal for high-power applications where rf break down is a concern. Design criteria, field-solver simulation results, and prototype measurements are presented.
△ Less
Submitted 12 February, 2001;
originally announced February 2001.
-
Planar Waveguide Hybrids for Very High Power RF
Authors:
C. D. Nantista,
W. R. Fowkes,
N. M. Kroll,
S. G. Tantawi
Abstract:
Two basic designs have been developed for waveguide hybrids, or 3-dB couplers, capable of handling hundreds of megawatts at X-band. Coupling is provided by one or two connecting waveguides with h-plane junctions and matching elements. In the former case, the connecting waveguide supports two modes. Small apertures and field-enhancing e-bends are avoided to reduce the risk of rf breakdown. The h-…
▽ More
Two basic designs have been developed for waveguide hybrids, or 3-dB couplers, capable of handling hundreds of megawatts at X-band. Coupling is provided by one or two connecting waveguides with h-plane junctions and matching elements. In the former case, the connecting waveguide supports two modes. Small apertures and field-enhancing e-bends are avoided to reduce the risk of rf breakdown. The h-plane symmetry also allows the use of over-moded rectangular waveguide in which the height has been increased to reduce field amplitudes without affecting the scattering matrix. The theory and designs are presented, along with the results of prototype tests of functionality and power-handling capability. Such a device is integral to the rf pulse compression or power distribution system of the Next Linear Collider (NLC) for combining, splitting, and directing power. This work was motivated by the observation of rf breakdown at power levels above 200 MW in conventional and modified magic-T's.
△ Less
Submitted 12 February, 2001;
originally announced February 2001.
-
New Development in RF Pulse Compression
Authors:
Sami G. Tantawi
Abstract:
Several pulse compression systems have been proposed for future linear collider. Most of these systems require hundreds of kilometers of low-loss waveguide runs. To reduce the waveguide length and improve the efficiency of these systems, components for multimoding, active switches and non-reciprocal elements are being developed. In the multimoded systems a waveguide is utilized several times by…
▽ More
Several pulse compression systems have been proposed for future linear collider. Most of these systems require hundreds of kilometers of low-loss waveguide runs. To reduce the waveguide length and improve the efficiency of these systems, components for multimoding, active switches and non-reciprocal elements are being developed. In the multimoded systems a waveguide is utilized several times by sending different signals over different modes. The multimoded components needed for these systems have to be able to handle hundreds of megawatts of rf power at the X-band frequency and above. Consequently, most of these components are overmoded. We present the development of multimoded components required for such systems. We also present the development efforts towards overmoded active component such as switches and overmoded non-reciprocal components such as circulators and isolators.
△ Less
Submitted 1 October, 2000; v1 submitted 20 August, 2000;
originally announced August 2000.
-
2D Simulation of High-Efficiency Cross-Field RF Power Sources
Authors:
Valery A. Dolgashev,
Sami G. Tantawi
Abstract:
An efficient method for frequency domain analysis of 2D cross-field devices is presented. This work was done to analyze and design high efficiency magnetrons. Arbitrary device-geometries are described by a piecewise planar boundary. The method is based on an expansion of the electromagnetic fields into a set of cavity eigenmodes. In order to obtain the self-consistent solution, iterations are pe…
▽ More
An efficient method for frequency domain analysis of 2D cross-field devices is presented. This work was done to analyze and design high efficiency magnetrons. Arbitrary device-geometries are described by a piecewise planar boundary. The method is based on an expansion of the electromagnetic fields into a set of cavity eigenmodes. In order to obtain the self-consistent solution, iterations are performed until the energy balance is reached. A boundary integration method is used to take into account space charge effects. The cavity eigenmodes are found by a method based on the scattering matrix technique. The geometry is divided into regions. The boundary contour mode-matching method is used to obtain the scattering matrices for each region. Electromagnetic fields in each region are expanded into a series of plane waves. Due to choice of plane wave expansion, all integration in the mode-matching process is carried out analytically. The scattering matrices of the regions are combined using a generalized scattering matrix technique to obtain the scattering matrix for the full geometry, and then the eigenmode resonance frequencies and the fields. Periodic boundary condition is used for the field calculation and the particle tracking.
△ Less
Submitted 20 August, 2000;
originally announced August 2000.
