-
STRASSE: A Silicon Tracker for Quasi-free Scattering Measurements at the RIBF
Authors:
H. N. Liu,
F. Flavigny,
H. Baba,
M. Boehmer,
U. Bonnes,
V. Borshchov,
P. Doornenbal,
N. Ebina,
M. Enciu,
A. Frotscher,
R. Gernhäuser,
V. Girard-Alcindor,
D. Goupillière,
J. Heuser,
R. Kapell,
Y. Kondo,
H. Lee,
J. Lehnert,
T. Matsui,
A. Matta,
T. Nakamura,
A. Obertelli,
T. Pohl,
M. Protsenko,
M. Sasano
, et al. (13 additional authors not shown)
Abstract:
STRASSE (Silicon Tracker for RAdioactive nuclei Studies at SAMURAI Experiments) is a new detection system under construction for quasi-free scattering (QFS) measurements at 200-250 MeV/nucleon at the RIBF facility of the RIKEN Nishina Center. It consists of a charged-particle silicon tracker coupled with a dedicated thick liquid hydrogen target (up to 150-mm long) in a compact geometry to fit insi…
▽ More
STRASSE (Silicon Tracker for RAdioactive nuclei Studies at SAMURAI Experiments) is a new detection system under construction for quasi-free scattering (QFS) measurements at 200-250 MeV/nucleon at the RIBF facility of the RIKEN Nishina Center. It consists of a charged-particle silicon tracker coupled with a dedicated thick liquid hydrogen target (up to 150-mm long) in a compact geometry to fit inside large scintillator or germanium arrays. Its design was optimized for two types of studies using QFS: missing-mass measurements and in-flight prompt $γ$-ray spectroscopy. This article describes (i) the resolution requirements needed to go beyond the sensitivity of existing systems for these two types of measurements, (ii) the conceptual design of the system using detailed simulations of the setup and (iii) its complete technical implementation and challenges. The final tracker aims at a sub-mm reaction vertex resolution and is expected to reach a missing-mass resolution below 2 MeV in $σ$ for $(p,2p)$ reactions when combined with the CsI(Na) CATANA array.
△ Less
Submitted 23 January, 2023;
originally announced January 2023.
-
Experimentally shock-induced melt veins in basalt: Improving the shock classification of eucrites
Authors:
Haruka Ono,
Kosuke Kurosawa,
Takafumi Niihara,
Takashi Mikouchi,
Naotaka Tomioka,
Junko Isa,
Hiroyuki Kagi,
Takuya Matsuzaki,
Hiroshi Sakuma,
Hidenori Genda,
Tatsuhiro Sakaiya,
Tadashi Kondo,
Masahiro Kayama,
Mizuho Koike,
Yuji Sano,
Masafumi Murayama,
Wataru Satake,
Takafumi Matsui
Abstract:
Basaltic rocks occur widely on the terrestrial planets and differentiated asteroids, including the asteroid 4 Vesta. We conducted a shock recovery experiment with decaying compressive pulses on a terrestrial basalt at Chiba Institute of Technology, Japan. The sample recorded a range of pressures, and shock physics modeling was conducted to add a pressure scale to the observed shock features. The s…
▽ More
Basaltic rocks occur widely on the terrestrial planets and differentiated asteroids, including the asteroid 4 Vesta. We conducted a shock recovery experiment with decaying compressive pulses on a terrestrial basalt at Chiba Institute of Technology, Japan. The sample recorded a range of pressures, and shock physics modeling was conducted to add a pressure scale to the observed shock features. The shocked sample was examined by optical and electron microscopy, electron back-scattered diffractometry, and Raman spectroscopy. We found that localized melting occurs at a lower pressure (~10 GPa) than previously thought (>20 GPa). The shocked basalt near the epicenter represents shock degree C of a recently proposed classification scheme for basaltic eucrites and, as such, our results provide a pressure scale for the classification scheme. Finally, we estimated the total fraction of the basaltic eucrites classified as shock degree C to be ~15% by assuming the impact velocity distribution onto Vesta.
△ Less
Submitted 21 December, 2022;
originally announced December 2022.
-
Shock recovery with decaying compressive pulses: Shock effects in calcite (CaCO$_3$) around the Hugoniot elastic limit
Authors:
Kosuke Kurosawa,
Haruka Ono,
Takafumi Niihara,
Tatsuhiro Sakaiya,
Tadashi Kondo,
Naotaka Tomioka,
Takashi Mikouchi,
Hidenori Genda,
Takuya Matsuzaki,
Masahiro Kayama,
Mizuho Koike,
Yuji Sano,
Masafumi Murayama,
Wataru Satake,
Takafumi Matsui
Abstract:
Shock metamorphism of minerals in meteorites provides insights into the ancient Solar System. Calcite is an abundant aqueous alteration mineral in carbonaceous chondrites. Return samples from the asteroids Ryugu and Bennu are expected to contain calcite-group minerals. Although shock metamorphism in silicates has been well studied, such data for aqueous alteration minerals are limited. Here, we in…
▽ More
Shock metamorphism of minerals in meteorites provides insights into the ancient Solar System. Calcite is an abundant aqueous alteration mineral in carbonaceous chondrites. Return samples from the asteroids Ryugu and Bennu are expected to contain calcite-group minerals. Although shock metamorphism in silicates has been well studied, such data for aqueous alteration minerals are limited. Here, we investigated the shock effects in calcite with marble using impact experiments at the Planetary Exploration Research Center of Chiba Institute of Technology. We produced decaying compressive pulses with a smaller projectile than the target. A metal container facilitates recovery of a sample that retains its pre-impact stratigraphy. We estimated the peak pressure distributions in the samples with the iSALE shock physics code. The capability of this method to produce shocked grains that have experienced different degrees of metamorphism from a single experiment is an advantage over conventional uniaxial shock recovery experiments. The shocked samples were investigated by polarizing microscopy and X-ray diffraction analysis. We found that more than half of calcite grains exhibit undulatory extinction when peak pressure exceeds 3 GPa. This shock pressure is one order of magnitude higher than the Hugoniot elastic limit (HEL) of marble, but it is close to the HEL of a calcite crystal, suggesting that the undulatory extinction records dislocation-induced plastic deformation in the crystal. Finally, we propose a strategy to re-construct the maximum depth of calcite grains in a meteorite parent body, if shocked calcite grains are identified in chondrites and/or return samples from Ryugu and Bennu.
△ Less
Submitted 19 May, 2022;
originally announced May 2022.
-
Tweet Analysis for Enhancement of COVID-19 Epidemic Simulation: A Case Study in Japan
Authors:
Vu Tran,
Tomoko Matsui
Abstract:
The COVID-19 pandemic, which began in December 2019, progressed in a complicated manner and thus caused problems worldwide. Seeking clues to the reasons for the complicated progression is necessary but challenging in the fight against the pandemic. We sought clues by investigating the relationship between reactions on social media and the COVID-19 epidemic in Japan. Twitter was selected as the soc…
▽ More
The COVID-19 pandemic, which began in December 2019, progressed in a complicated manner and thus caused problems worldwide. Seeking clues to the reasons for the complicated progression is necessary but challenging in the fight against the pandemic. We sought clues by investigating the relationship between reactions on social media and the COVID-19 epidemic in Japan. Twitter was selected as the social media platform for study because it has a large user base in Japan and because it quickly propagates short topic-focused messages ("tweets"). Analysis using Japanese Twitter data suggests that reactions on social media and the progression of the COVID-19 pandemic may have a close relationship. Experiments to evaluate the potential of using tweets to support the prediction of how an epidemic will progress demonstrated the value of using epidemic-related social media data. Our findings provide insights into the relationship between user reactions on social media, particularly Twitter, and epidemic progression, which can be used to fight pandemics.
△ Less
Submitted 29 October, 2021;
originally announced November 2021.
-
Wrinkle force microscopy: a new machine learning based approach to predict cell mechanics from images
Authors:
Honghan Li,
Daiki Matsunaga,
Tsubasa S. Matsui,
Hiroki Aosaki,
Koki Inoue,
Amin Doostmohammadi,
Shinji Deguchi
Abstract:
Combining experiments with artificial intelligence algorithms, we propose a new machine learning based approach to extract the cellular force distributions from the microscope images. The full process can be divided into three steps. First, we culture the cells on a special substrate allowing to measure both the cellular traction force on the substrate and the corresponding substrate wrinkles simu…
▽ More
Combining experiments with artificial intelligence algorithms, we propose a new machine learning based approach to extract the cellular force distributions from the microscope images. The full process can be divided into three steps. First, we culture the cells on a special substrate allowing to measure both the cellular traction force on the substrate and the corresponding substrate wrinkles simultaneously. The cellular forces are obtained using the traction force microscopy (TFM), at the same time that cell-generated contractile forces wrinkle their underlying substrate. Second, the wrinkle positions are extracted from the microscope images. Third, we train the machine learning system with GAN (generative adversarial network) by using sets of corresponding two images, the traction field and the input images (raw microscope images or extracted wrinkle images), as the training data. The network understands the way to convert the input images of the substrate wrinkles to the traction distribution from the training. After sufficient training, the network is utilized to predict the cellular forces just from the input images. Our system provides a powerful tool to evaluate the cellular forces efficiently because the forces can be predicted just by observing the cells under the microscope, which is a way simpler method compared to the TFM experiment. Additionally, the machine learning based approach presented here has the profound potential for being applied to diverse cellular assays for studying mechanobiology of cells.
△ Less
Submitted 24 February, 2021;
originally announced February 2021.
-
Image based cellular contractile force evaluation with small-world network inspired CNN: SW-UNet
Authors:
Li Honghan,
Daiki Matsunaga,
Tsubasa S. Matsui,
Hiroki Aosaki,
Shinji Deguchi
Abstract:
We propose an image-based cellular contractile force evaluation method using a machine learning technique. We use a special substrate that exhibits wrinkles when cells grab the substrate and contract, and the wrinkles can be used to visualize the force magnitude and direction. In order to extract wrinkles from the microscope images, we develop a new CNN (convolutional neural network) architecture…
▽ More
We propose an image-based cellular contractile force evaluation method using a machine learning technique. We use a special substrate that exhibits wrinkles when cells grab the substrate and contract, and the wrinkles can be used to visualize the force magnitude and direction. In order to extract wrinkles from the microscope images, we develop a new CNN (convolutional neural network) architecture SW-UNet (small-world U-Net), which is a CNN that reflects the concept of the small-world network. The SW-UNet shows better performance in wrinkle segmentation task compared to other methods: the error (Euclidean distance) of SW-UNet is 4.9 times smaller than 2D-FFT (fast Fourier transform) based segmentation approach, and is 2.9 times smaller than U-Net. As a demonstration, we compare the contractile force of U2OS (human osteosarcoma) cells and show that cells with a mutation in the KRAS oncogne show larger force compared to the wild-type cells. Our new machine learning based algorithm provides us an efficient, automated and accurate method to evaluate the cell contractile force.
△ Less
Submitted 22 August, 2019;
originally announced August 2019.
-
Hexagonal Nanopits with the Zigzag Edge State on Graphite Surfaces Synthesized by Hydrogen-Plasma Etching
Authors:
Tomohiro Matsui,
Hideki Sato,
Kazuma Kita,
André E. B. Amend,
Hiroshi Fukuyama
Abstract:
We studied, by scanning tunneling microscopy, the morphology of nanopits of monolayer depth created at graphite surfaces by hydrogen plasma etching under various conditions such as H$_2$ pressure, temperature, etching time, and RF power of the plasma generation. In addition to the known pressure-induced transition of the nanopit morphology, we found a sharp temperature-induced transition from many…
▽ More
We studied, by scanning tunneling microscopy, the morphology of nanopits of monolayer depth created at graphite surfaces by hydrogen plasma etching under various conditions such as H$_2$ pressure, temperature, etching time, and RF power of the plasma generation. In addition to the known pressure-induced transition of the nanopit morphology, we found a sharp temperature-induced transition from many small rather round nanopits of ~150 nm size to few large hexagonal ones of 300-600 nm within a narrow temperature range. The remote and direct plasma modes switching mechanism, which was proposed to explain the pressure-induced transition, is not directly applicable to this newly found transition. Scanning tunneling spectroscopy (STS) measurements of edges of the hexagonal nanopits fabricated at graphite surfaces by this method show clear signatures of the peculiar electronic state localized at the zigzag edge (edge state), i.e., a prominent peak near the Fermi energy accompanied by suppressions on either side in the local density of states. These observations indicate that the hexagonal nanopits consist of a high density of zigzag edges. The STS data also revealed a domain structure of the edge state in which the electronic state varies over a length scale of ~3 nm along the edge. The present study will pave the way for microscopic understanding of the anisotropic etching mechanism and of spin polarization in zigzag nanoribbons which are promising key elements for future graphene nanoelectronics.
△ Less
Submitted 31 July, 2019;
originally announced August 2019.
-
First cryogenic test operation of underground km-scale gravitational-wave observatory KAGRA
Authors:
KAGRA Collaboration,
T. Akutsu,
M. Ando,
K. Arai,
Y. Arai,
S. Araki,
A. Araya,
N. Aritomi,
H. Asada,
Y. Aso,
S. Atsuta,
K. Awai,
S. Bae,
L. Baiotti,
M. A. Barton,
K. Cannon,
E. Capocasa,
C-S. Chen,
T-W. Chiu,
K. Cho,
Y-K. Chu,
K. Craig,
W. Creus,
K. Doi,
K. Eda
, et al. (179 additional authors not shown)
Abstract:
KAGRA is a second-generation interferometric gravitational-wave detector with 3-km arms constructed at Kamioka, Gifu in Japan. It is now in its final installation phase, which we call bKAGRA (baseline KAGRA), with scientific observations expected to begin in late 2019. One of the advantages of KAGRA is its underground location of at least 200 m below the ground surface, which brings small seismic…
▽ More
KAGRA is a second-generation interferometric gravitational-wave detector with 3-km arms constructed at Kamioka, Gifu in Japan. It is now in its final installation phase, which we call bKAGRA (baseline KAGRA), with scientific observations expected to begin in late 2019. One of the advantages of KAGRA is its underground location of at least 200 m below the ground surface, which brings small seismic motion at low frequencies and high stability of the detector. Another advantage is that it cools down the sapphire test mass mirrors to cryogenic temperatures to reduce thermal noise. In April-May 2018, we have operated a 3-km Michelson interferometer with a cryogenic test mass for 10 days, which was the first time that km-scale interferometer was operated at cryogenic temperatures. In this article, we report the results of this "bKAGRA Phase 1" operation. We have demonstrated the feasibility of 3-km interferometer alignment and control with cryogenic mirrors.
△ Less
Submitted 11 January, 2019;
originally announced January 2019.
-
Vibration isolation system with a compact damping system for power recycling mirrors of KAGRA
Authors:
Y. Akiyama,
T. Akutsu,
M. Ando,
K. Arai,
Y. Arai,
S. Araki,
A. Araya,
N. Aritomi,
H. Asada,
Y. Aso,
S. Bae,
L. Baiotti,
M. A. Barton,
K. Cannon,
E. Capocasa,
C-S. Chen,
T-W. Chiu,
K. Cho,
Y-K. Chu,
K. Craig,
V. Dattilo,
K. Doi,
Y. Enomoto,
R. Flaminio,
Y. Fujii
, et al. (149 additional authors not shown)
Abstract:
A vibration isolation system called Type-Bp system used for power recycling mirrors has been developed for KAGRA, the interferometric gravitational-wave observatory in Japan. A suspension of the Type-Bp system passively isolates an optic from seismic vibration using three main pendulum stages equipped with two vertical vibration isolation systems. A compact reaction mass around each of the main st…
▽ More
A vibration isolation system called Type-Bp system used for power recycling mirrors has been developed for KAGRA, the interferometric gravitational-wave observatory in Japan. A suspension of the Type-Bp system passively isolates an optic from seismic vibration using three main pendulum stages equipped with two vertical vibration isolation systems. A compact reaction mass around each of the main stages allows for achieving sufficient damping performance with a simple feedback as well as vibration isolation ratio. Three Type-Bp systems were installed in KAGRA, and were proved to satisfy the requirements on the damping performance, and also on estimated residual displacement of the optics.
△ Less
Submitted 10 January, 2019;
originally announced January 2019.
-
KAGRA: 2.5 Generation Interferometric Gravitational Wave Detector
Authors:
T. Akutsu,
M. Ando,
K. Arai,
Y. Arai,
S. Araki,
A. Araya,
N. Aritomi,
H. Asada,
Y. Aso,
S. Atsuta,
K. Awai,
S. Bae,
L. Baiotti,
M. A. Barton,
K. Cannon,
E. Capocasa,
C-S. Chen,
T-W. Chiu,
K. Cho,
Y-K. Chu,
K. Craig,
W. Creus,
K. Doi,
K. Eda,
Y. Enomoto
, et al. (169 additional authors not shown)
Abstract:
The recent detections of gravitational waves (GWs) reported by LIGO/Virgo collaborations have made significant impact on physics and astronomy. A global network of GW detectors will play a key role to solve the unknown nature of the sources in coordinated observations with astronomical telescopes and detectors. Here we introduce KAGRA (former name LCGT; Large-scale Cryogenic Gravitational wave Tel…
▽ More
The recent detections of gravitational waves (GWs) reported by LIGO/Virgo collaborations have made significant impact on physics and astronomy. A global network of GW detectors will play a key role to solve the unknown nature of the sources in coordinated observations with astronomical telescopes and detectors. Here we introduce KAGRA (former name LCGT; Large-scale Cryogenic Gravitational wave Telescope), a new GW detector with two 3-km baseline arms arranged in the shape of an "L", located inside the Mt. Ikenoyama, Kamioka, Gifu, Japan. KAGRA's design is similar to those of the second generations such as Advanced LIGO/Virgo, but it will be operating at the cryogenic temperature with sapphire mirrors. This low temperature feature is advantageous for improving the sensitivity around 100 Hz and is considered as an important feature for the third generation GW detector concept (e.g. Einstein Telescope of Europe or Cosmic Explorer of USA). Hence, KAGRA is often called as a 2.5 generation GW detector based on laser interferometry. The installation and commissioning of KAGRA is underway and its cryogenic systems have been successfully tested in May, 2018. KAGRA's first observation run is scheduled in late 2019, aiming to join the third observation run (O3) of the advanced LIGO/Virgo network. In this work, we describe a brief history of KAGRA and highlights of main feature. We also discuss the prospects of GW observation with KAGRA in the era of O3. When operating along with the existing GW detectors, KAGRA will be helpful to locate a GW source more accurately and to determine the source parameters with higher precision, providing information for follow-up observations of a GW trigger candidate.
△ Less
Submitted 20 November, 2018;
originally announced November 2018.
-
Construction of KAGRA: an Underground Gravitational Wave Observatory
Authors:
T. Akutsu,
M. Ando,
S. Araki,
A. Araya,
T. Arima,
N. Aritomi,
H. Asada,
Y. Aso,
S. Atsuta,
K. Awai,
L. Baiotti,
M. A. Barton,
D. Chen,
K. Cho,
K. Craig,
R. DeSalvo,
K. Doi,
K. Eda,
Y. Enomoto,
R. Flaminio,
S. Fujibayashi,
Y. Fujii,
M. -K. Fujimoto,
M. Fukushima,
T. Furuhata
, et al. (202 additional authors not shown)
Abstract:
Major construction and initial-phase operation of a second-generation gravitational-wave detector KAGRA has been completed. The entire 3-km detector is installed underground in a mine in order to be isolated from background seismic vibrations on the surface. This allows us to achieve a good sensitivity at low frequencies and high stability of the detector. Bare-bones equipment for the interferomet…
▽ More
Major construction and initial-phase operation of a second-generation gravitational-wave detector KAGRA has been completed. The entire 3-km detector is installed underground in a mine in order to be isolated from background seismic vibrations on the surface. This allows us to achieve a good sensitivity at low frequencies and high stability of the detector. Bare-bones equipment for the interferometer operation has been installed and the first test run was accomplished in March and April of 2016 with a rather simple configuration. The initial configuration of KAGRA is named {\it iKAGRA}. In this paper, we summarize the construction of KAGRA, including the study of the advantages and challenges of building an underground detector and the operation of the iKAGRA interferometer together with the geophysics interferometer that has been constructed in the same tunnel.
△ Less
Submitted 11 December, 2017; v1 submitted 30 November, 2017;
originally announced December 2017.
-
The status of KAGRA underground cryogenic gravitational wave telescope
Authors:
KAGRA Collaboration,
T. Akutsu,
M. Ando,
A. Araya,
N. Aritomi,
H. Asada,
Y. Aso,
S. Atsuta,
K. Awai,
M. A. Barton,
K. Cannon,
K. Craig,
W. Creus,
K. Doi,
K. Eda,
Y. Enomoto,
R. Flaminio,
Y. Fujii,
M. -K. Fujimoto,
T. Furuhata,
S. Haino,
K. Hasegawa,
K. Hashino,
K. Hayama,
S. Hirobayashi
, et al. (126 additional authors not shown)
Abstract:
KAGRA is a 3-km interferometric gravitational wave telescope located in the Kamioka mine in Japan. It is the first km-class gravitational wave telescope constructed underground to reduce seismic noise, and the first km-class telescope to use cryogenic cooling of test masses to reduce thermal noise. The construction of the infrastructure to house the interferometer in the tunnel, and the initial ph…
▽ More
KAGRA is a 3-km interferometric gravitational wave telescope located in the Kamioka mine in Japan. It is the first km-class gravitational wave telescope constructed underground to reduce seismic noise, and the first km-class telescope to use cryogenic cooling of test masses to reduce thermal noise. The construction of the infrastructure to house the interferometer in the tunnel, and the initial phase operation of the interferometer with a simple 3-km Michelson configuration have been completed. The first cryogenic operation is expected in 2018, and the observing runs with a full interferometer are expected in 2020s. The basic interferometer configuration and the current status of KAGRA are described.
△ Less
Submitted 13 October, 2017;
originally announced October 2017.
-
Additive Approximation Algorithms for Modularity Maximization
Authors:
Yasushi Kawase,
Tomomi Matsui,
Atsushi Miyauchi
Abstract:
The modularity is a quality function in community detection, which was introduced by Newman and Girvan (2004). Community detection in graphs is now often conducted through modularity maximization: given an undirected graph $G=(V,E)$, we are asked to find a partition $\mathcal{C}$ of $V$ that maximizes the modularity. Although numerous algorithms have been developed to date, most of them have no th…
▽ More
The modularity is a quality function in community detection, which was introduced by Newman and Girvan (2004). Community detection in graphs is now often conducted through modularity maximization: given an undirected graph $G=(V,E)$, we are asked to find a partition $\mathcal{C}$ of $V$ that maximizes the modularity. Although numerous algorithms have been developed to date, most of them have no theoretical approximation guarantee. Recently, to overcome this issue, the design of modularity maximization algorithms with provable approximation guarantees has attracted significant attention in the computer science community.
In this study, we further investigate the approximability of modularity maximization. More specifically, we propose a polynomial-time $\left(\cos\left(\frac{3-\sqrt{5}}{4}π\right) - \frac{1+\sqrt{5}}{8}\right)$-additive approximation algorithm for the modularity maximization problem. Note here that $\cos\left(\frac{3-\sqrt{5}}{4}π\right) - \frac{1+\sqrt{5}}{8} < 0.42084$ holds. This improves the current best additive approximation error of $0.4672$, which was recently provided by Dinh, Li, and Thai (2015). Interestingly, our analysis also demonstrates that the proposed algorithm obtains a nearly-optimal solution for any instance with a very high modularity value. Moreover, we propose a polynomial-time $0.16598$-additive approximation algorithm for the maximum modularity cut problem. It should be noted that this is the first non-trivial approximability result for the problem. Finally, we demonstrate that our approximation algorithm can be extended to some related problems.
△ Less
Submitted 13 January, 2016;
originally announced January 2016.
-
Deciphering the measured ratios of Iodine-131 to Cesium-137 at the Fukushima reactors
Authors:
T. Matsui
Abstract:
We calculate the relative abundance of the radioactive isotopes Iodine-131 and Cesium-137 produced by nuclear fission in reactors and compare it with data taken at the troubled Fukushima Dai-ichi nuclear power plant. The ratio of radioactivities of these two isotopes can be used to obtain information about when the nuclear reactions terminated.
We calculate the relative abundance of the radioactive isotopes Iodine-131 and Cesium-137 produced by nuclear fission in reactors and compare it with data taken at the troubled Fukushima Dai-ichi nuclear power plant. The ratio of radioactivities of these two isotopes can be used to obtain information about when the nuclear reactions terminated.
△ Less
Submitted 13 December, 2011; v1 submitted 2 May, 2011;
originally announced May 2011.
-
Scanning tunneling microscopy and spectroscopy studies of graphite edges
Authors:
Y. Niimi,
T. Matsui,
H. Kambara,
K. Tagami,
M. Tsukada,
Hiroshi Fukuyama
Abstract:
We studied experimentally and theoretically the electronic local density of states (LDOS) near single step edges at the surface of exfoliated graphite. In scanning tunneling microscopy measurements, we observed the $(\sqrt{3} \times \sqrt{3}) R 30^{\circ}$ and honeycomb superstructures extending over 3$-$4 nm both from the zigzag and armchair edges. Calculations based on a density-functional der…
▽ More
We studied experimentally and theoretically the electronic local density of states (LDOS) near single step edges at the surface of exfoliated graphite. In scanning tunneling microscopy measurements, we observed the $(\sqrt{3} \times \sqrt{3}) R 30^{\circ}$ and honeycomb superstructures extending over 3$-$4 nm both from the zigzag and armchair edges. Calculations based on a density-functional derived non-orthogonal tight-binding model show that these superstructures can coexist if the two types of edges admix each other in real graphite step edges. Scanning tunneling spectroscopy measurements near the zigzag edge reveal a clear peak in the LDOS at an energy below the Fermi energy by 20 meV. No such a peak was observed near the armchair edge. We concluded that this peak corresponds to the "edge state" theoretically predicted for graphene ribbons, since a similar prominent LDOS peak due to the edge state is obtained by the first principles calculations.
△ Less
Submitted 2 May, 2005; v1 submitted 14 April, 2004;
originally announced April 2004.