Metal L-edge

Figure 1: L₃- and L₂-edges of [CuCl₄]²⁻.

Metal L-edge spectroscopy is a spectroscopic technique used to study the electronic structures of transition metal atoms and complexes. This method measures X-ray absorption caused by the excitation of a metal 2p electron to unfilled d orbitals (e.g. 3d for first-row transition metals), which creates a characteristic absorption peak called the L-edge. Similar features can also be studied by Electron Energy Loss Spectroscopy. According to the selection rules, the transition is formally electric-dipole allowed, which not only makes it more intense than an electric-dipole forbidden metal K pre-edge (1s → 3d) transition, but also makes it more feature-rich as the lower required energy (~400-1000 eV from scandium to copper) results in a higher-resolution experiment.

In the simplest case, that of a cupric (Cu^II) complex, the 2p → 3d transition produces a 2p⁵3d¹⁰ final state. The 2p⁵ core hole created in the transition has an orbital angular momentum L=1 which then couples to the spin angular momentum S=1/2 to produce J=3/2 and J=1/2 final states. These states are directly observable in the L-edge spectrum as the two main peaks (Figure 1). The peak at lower energy (~930 eV) has the greatest intensity and is called the L₃-edge, while the peak at higher energy (~950 eV) has less intensity and is called the L₂-edge.

Spectral components

Figure 2: L-edge spectral components.

As we move left across the periodic table (e.g. from copper to iron), we create additional holes in the metal 3d orbitals. For example, a low-spin ferric (Fe^III) system in an octahedral environment has a ground state of (t_2g)⁵(e_g)⁰ resulting in transitions to the t_2g (dπぱい) and e_g (dσしぐま) sets. Therefore, there are two possible final states: t_2g⁶e_g⁰ or t_2g⁵e_g¹(Figure 2a). Since the ground-state metal configuration has four holes in the e_g orbital set and one hole in the t_2g orbital set, an intensity ratio of 4:1 might be expected (Figure 2b). However, this model does not take into account covalent bonding and, indeed, an intensity ratio of 4:1 is not observed in the spectrum.

In the case of iron, the d⁶ excited state will further split in energy due to d-d electron repulsion (Figure 2c). This splitting is given by the right-hand (high-field) side of the d⁶ Tanabe–Sugano diagram and can be mapped onto a theoretical simulation of a L-edge spectrum (Figure 2d). Other factors such as p-d electron repulsion and spin-orbit coupling of the 2p and 3d electrons must also be considered to fully simulate the data.

For a ferric system, all of these effects result in 252 initial states and 1260 possible final states that together will comprise the final L-edge spectrum (Figure 2e). Despite all of these possible states, it has been established that in a low-spin ferric system, the lowest energy peak is due to a transition to the t_2g hole and the more intense and higher energy (~3.5 eV) peak is to that of the unoccupied e_g orbitals.

Feature mixing

Figure 3: Configurations involved in the ground and excited states and the mechanisms by which the intensity of the L-edge features can mix.

In most systems, bonding between a ligand and a metal atom can be thought of in terms of metal-ligand covalent bonds, where the occupied ligand orbitals donate some electron density to the metal. This is commonly known as ligand-to-metal charge transfer or LMCT. In some cases, low-lying unoccupied ligand orbitals (πぱい*) can receive back-donation (or backbonding) from the occupied metal orbitals. This has the opposite effect on the system, resulting in metal-to-ligand charge transfer, MLCT, and commonly appears as an additional L-edge spectral feature.

An example of this feature occurs in low-spin ferric [Fe(CN)₆]³⁻, since CN⁻ is a ligand that can have backbonding. While backbonding is important in the initial state, it would only warrant a small feature in the L-edge spectrum. In fact, it is in the final state where the backbonding πぱい* orbitals are allowed to mix with the very intense e_g transition, thus borrowing intensity and resulting in the final dramatic three peak spectrum (Figure 3 and Figure 4).

Model construction

Figure 4: Comparison of the Fe L-edges of low-spin K₃[Fe(CN)₆] and [Fe(tacn)₂]Cl₃. Tacn is a σしぐま-only donor, meaning no backbonding and only two main L-edge features. K₃[Fe(CN)₆] has significant backbonding, as is shown by the third transition to higher energy in the L-edge spectrum.

X-ray absorption spectroscopy (XAS), like other spectroscopies, looks at the excited state to infer information about the ground state. To make a quantitative assignment, L-edge data is fitted using a valence bond configuration interaction (VBCI) model where LMCT and MLCT are applied as needed to successfully simulate the observed spectral features. These simulations are then further compared to density functional theory (DFT) calculations to arrive at a final interpretation of the data and an accurate description of the electronic structure of the complex (Figure 4).

In the case of iron L-edge, the excited state mixing of the metal e_g orbitals into the ligand πぱい* make this method a direct and very sensitive probe of backbonding.

See also

• Metal K-edge
• Ligand K-edge
• Extended X-ray absorption fine structure